Learn About Tire Age and Inspection Methods

Understanding Tire Age and Why It Matters

Tires are one of the most important safety features on any vehicle. They are the only part of your car that touches the road, which means they affect how your vehicle handles, stops, and performs in different weather conditions. While many people focus on tire tread depth, tire age is equally important for safety. Tires degrade over time, even when they are not being used, due to exposure to sunlight, heat, humidity, and ozone in the air. The rubber compounds in tires break down gradually, which can affect the tire's ability to grip the road and resist damage.

Free Guide to Logging Into Peacock With Spectrum →

The National Highway Traffic Safety Administration (NHTSA) and tire manufacturers recommend that tires be replaced every 6 to 10 years, regardless of how much tread remains. This recommendation exists because the structural integrity of the tire changes as it ages. Research has shown that tires older than 10 years are significantly more likely to fail, which can lead to blowouts, loss of vehicle control, and accidents. Some tire manufacturers are even more conservative, suggesting replacement at 6 years for tires in regular use.

Age-related tire failure is not always visible to the eye. A tire might look fine on the outside but have internal structural damage that makes it unsafe. This is why tire age is considered just as important as tread depth when determining if a tire is safe to use. Understanding how to determine the age of your tires is a skill every vehicle owner should have, along with knowing when replacement becomes necessary for safety reasons.

Practical Takeaway: Check the age of your current tires this month. Make a note of when they were manufactured, and create a reminder to monitor their condition. If your tires are approaching 6 years old, consider planning for replacement even if the tread looks acceptable.

How to Find Your Tire's Manufacturing Date

Every tire sold in the United States has a Department of Transportation (DOT) identification number stamped on the sidewall. This number contains important information about where and when the tire was made, and it is the key to determining your tire's age. The DOT code is typically a long series of characters, but the manufacturing date is found in the last four digits of this code. Learning to read this code takes just a few minutes of practice.

How to Close Apps on Android Phones →

To locate the DOT number, walk around your vehicle and look at the sidewall of each tire. The DOT code will be printed or molded into the rubber and will start with the letters "DOT." It may be on either the inner or outer sidewall of the tire. Once you find it, look at the final four digits. These four numbers tell you when the tire was manufactured. The first two digits represent the week of the year the tire was made (ranging from 01 to 53), and the last two digits represent the year. For example, if the last four digits read "3519," this means the tire was manufactured during week 35 of 2019.

Before 2000, the DOT code had only three digits for the date, which made it harder to determine if tires were very old. If you encounter a tire with a three-digit date code, you cannot reliably determine its age, and it should be considered potentially unsafe. Most tire shops and mechanics can help you locate and read the DOT code if you are unsure how to find it yourself. This information is also useful when purchasing used tires or when inspecting tires on a vehicle you are considering buying.

Practical Takeaway: Go to your vehicle now and write down the last four digits of the DOT code for each tire. Convert these numbers into a manufacturing date using the system described above. This gives you a clear picture of how old your tires are and when you may need to plan for replacement.

Visual Inspection Methods for Tire Condition

While knowing a tire's age is important, visual inspection of the tire's physical condition provides additional information about whether a tire is safe to use. Even relatively new tires can be damaged by impacts, punctures, or improper inflation, while older tires may look acceptable on the surface but have internal issues. A thorough visual inspection involves checking several different aspects of the tire, and most of these checks can be done by any vehicle owner without special tools or training.

Learn How to Replace Your Car's Ignition Cylinder →

Start by examining the tread of the tire. Tire tread depth is measured in 32nds of an inch, and the legal minimum in most places is 2/32 of an inch. A simple method to check tread depth is the penny test. Insert a penny into the tread grooves with Lincoln's head facing downward. If the top of Lincoln's head disappears into the tread, your tire has adequate tread depth. If you can see the top of his head, the tread is too shallow and the tire should be replaced. For wet weather performance, many safety experts recommend replacing tires when tread depth reaches 4/32 of an inch, which is less than the legal minimum but provides better water evacuation and reduces the risk of hydroplaning.

Next, look for visible damage on the tire sidewall and tread area. Check for cracks, cuts, bulges, or blisters in the rubber. Small cuts less than 1/4 inch long and less than 1/8 inch wide in the tread area may sometimes be repaired, but cuts or damage on the sidewall cannot be safely repaired and the tire should be replaced. Bulges or blisters indicate that the internal structure of the tire has been damaged, usually from hitting a pothole or curb, and replacement is necessary. Also inspect the valve stem, which is the small protrusion where air goes into the tire. If it appears cracked, corroded, or damaged, it may leak air and should be replaced.

Check the overall wear pattern of the tire by running your hand around the entire circumference of the tire. The wear should be relatively even around the tire. Uneven wear patterns, such as excessive wear on the inner or outer edges, or wear concentrated in the center of the tire, can indicate problems with wheel alignment, suspension, or tire inflation. These issues should be addressed by a qualified mechanic, and the tires may need to be replaced if the damage is severe.

Practical Takeaway: Perform a visual inspection of all four tires this week. Use the penny test to check tread depth, look for any cuts or bulges in the rubber, and examine the wear pattern. Document your findings, and if you find any concerns, have the tires inspected by a professional tire technician.

Professional Tire Inspection and What to Expect

While vehicle owners can perform basic visual inspections of their tires, a professional inspection by a trained tire technician provides a more thorough evaluation. Professional inspectors have specialized equipment and training to detect problems that may not be visible during a casual inspection at home. Many tire shops and automotive service centers offer free tire inspections, and this service is worth taking advantage of periodically, particularly for older tires or if you notice any changes in how your vehicle handles.

Free Guide to Diabetes Care Options in Norman →

During a professional inspection, a technician will use a depth gauge to measure tread depth more accurately than the penny test. They will also use a tire pressure monitoring system to check the air pressure in each tire and compare it to the manufacturer's recommendations. Proper tire inflation is critical for safety, fuel efficiency, and tire longevity. Under-inflated tires wear out faster and can generate excess heat, which may lead to failure. Over-inflated tires wear unevenly and provide a harsher ride. A professional will also inspect for uneven wear patterns and can identify alignment or suspension issues that may be causing the problem.

Some tire shops use advanced inspection methods, including tire dismounting and internal inspection for damage that cannot be seen from the outside. If a tire is suspected of having internal damage or if it has been driven on while flat or severely under-inflated, this type of inspection can reveal problems that may make the tire unsafe. Some shops also have equipment to measure sidewall damage and assess whether a tire can be repaired or must be replaced. The cost of a professional inspection is typically minimal or free, making it a reasonable investment in your vehicle's safety.

When you take your vehicle in for an inspection, ask the technician to explain their findings to you. A reputable shop will show you any problem areas and explain their recommendations for repair or replacement. They should provide this information in writing and be willing to answer your questions. If you are uncertain about their recommendations, you can always seek a second opinion from another tire shop before making any decisions.

Practical Takeaway: Schedule a professional tire inspection at a local tire shop