Oil changes rank among the most frequently performed vehicle maintenance tasks in the United States. According to the American Petroleum Institute, roughly 55% of vehicle owners either change their own oil or have someone change it for them rather than visiting a dealership. The economics are straightforward: a professional oil change typically costs between $35 and $75 depending on your vehicle type and oil grade, while doing it yourself usually costs $15 to $40 for the oil and filter alone.
Learn About Paying Your FGUA Bill Online →
But cost isn't the only reason people tackle this job themselves. Many vehicle owners find that learning to change their own oil builds practical knowledge about how their engine works. It also means you control the timing—you're not waiting for an appointment or dealing with service department schedules. Some people simply prefer understanding exactly what goes into their vehicle rather than trusting someone else with the task.
Before you decide this is for you, consider what the job actually involves. Changing your oil requires getting under your vehicle, handling hot liquids, and disposing of used oil properly. It takes most people 30 to 45 minutes their first time, though experienced DIYers can finish in 15 to 20 minutes. You'll need a basic set of tools and some workspace—ideally a garage or driveway with level ground.
The environmental factor matters too. Used motor oil contains heavy metals and hydrocarbons that damage soil and water if dumped improperly. When you change your own oil, you become responsible for disposing of it correctly. Many auto parts stores accept used oil for free, as do some municipal hazardous waste facilities. This responsibility is one reason some vehicle owners prefer letting professionals handle it.
Practical takeaway: Decide whether changing your own oil fits your situation based on available time, workspace, comfort working under a vehicle, and willingness to dispose of waste oil properly—not just on potential savings.
Changing your own oil doesn't require an expensive toolkit. Most successful DIYers work with items that cost less than $50 total and fit in a small box. The question isn't whether you have enough tools—it's whether you have the right ones.
Free Guide to Pay by Plate Illinois Billing →
Start with an oil drain pan. This catches the old oil when you remove the drain plug. Any container that holds at least 6 to 8 quarts works, though a dedicated drain pan with a spout makes pouring used oil into storage containers much easier. A basic plastic pan costs around $8 to $12.
Next, you need a way to remove the old oil filter. Most vehicles use a spin-on filter that you remove by hand or with a filter wrench. A filter wrench is a metal or rubber tool that grips the cylindrical filter and lets you unscrew it. Hand-tightening usually works for reinstallation, so you may not need a filter wrench at all on your first attempt—but having one prevents stripped filters and costs only $6 to $15. Some people use an old leather belt or rubber glove for extra grip instead.
The third essential tool is a socket wrench or wrench that fits your oil drain plug. Most vehicles use either a 13mm, 14mm, 15mm, or 17mm bolt. Check your owner's manual or search your vehicle model online before buying. A basic socket wrench set costs $15 to $25 and handles this job plus countless others around your home.
You'll also need:
The total materials cost for oil and filter ranges from $20 to $50, depending on your vehicle size and the oil brand you select. Synthetic oil costs more than conventional but lasts longer between changes.
Practical takeaway: Buy an oil drain pan, a filter wrench, the correct socket wrench size, new oil in your vehicle's specified grade, and a new filter—these five items handle about 95% of what you'll actually need.
The oil drain plug sits at the lowest point of your engine's oil pan—the container that holds all the oil your engine uses. On most vehicles, it's underneath and toward the back of the engine. Finding it means getting a good look under your vehicle, which is where jack stands become important. Never crawl completely under a vehicle supported only by a hydraulic jack, as they can fail suddenly.
Free Guide to Mold Removal Methods for Walls →
To find your drain plug safely: position your vehicle on level ground, engage the parking brake, and place wheel chocks (or bricks) behind the rear wheels. Use a hydraulic jack to raise one side of the vehicle. Immediately place a jack stand under the frame, lower the vehicle onto the stand, then raise the other side and place a second stand. Now you can safely work underneath.
Once you're underneath with a flashlight, look for a bolt sticking out of the lowest part of the engine. It's typically between one-half inch and three-quarter inch in diameter. Some vehicles have a protective skid plate beneath the engine that you may need to remove first—this usually requires removing 4 to 8 bolts.
Before you remove the drain plug, understand what's about to happen. Engine oil circulating through your engine absorbs heat, dirt particles, and byproducts of combustion. After 3,000 to 10,000 miles (depending on oil type), the oil becomes dark and loses its ability to protect engine parts effectively. This old oil is still warm from running the engine, so let your vehicle cool for 5 to 10 minutes before starting—hot oil can cause serious burns.
The drained oil appears dark brown or nearly black. You'll notice it may smell strongly of fuel or have a slightly burnt odor. This is normal. The amount that drains out varies by vehicle—typically between 4 and 8 quarts. A quart equals roughly one liter. Watch how much drains out, as you'll need to add roughly that amount of new oil later.
Some people are surprised that oil doesn't drain completely. About one-half quart usually remains in the engine even after the pan drains. This is expected and doesn't require flushing out unless your owner's manual recommends an oil flush for high-mileage engines.
Practical takeaway: Use jack stands properly before working under your vehicle, find the drain plug at the engine pan's lowest point, let the engine cool first, and expect the old oil to be dark and warm—prepare containers and towels before you begin.
Once old oil stops draining from the plug, you'll address the oil filter. The filter removes microscopic dirt and particles that circulate with engine oil. Over time, the filter catches so much debris that oil can't flow through it efficiently. Replacing it with every oil change is standard practice.
How to Delete Your Fitbit Account Guide →
Locate your oil filter—usually a cylinder about 3 to 4 inches tall mounted on the side of the engine. You'll access it from above without needing to stay underneath. To remove it, position your drain pan underneath (some oil remains inside the filter), then use a filter wrench or your hand to turn it counterclockwise. Most filters spin off by hand, though older vehicles or tight filters may require a wrench.
Before installing the new filter, wipe the filter mount surface with a clean rag. This removes old oil and debris that could prevent a proper seal. Take your new filter and apply a thin layer of new oil to the rubber gasket (the soft ring around the top). This creates a watertight seal when you install it.
Screw the new filter on by hand until the gasket contacts the mounting surface, then rotate it an additional three-quarter turn. Don't use a filter wrench to tighten it—hand-tight is
This guide is for general information only and is not medical, financial, legal, or other professional advice. For decisions specific to your situation, consult a qualified professional. See our Editorial Policy.