A gas stove igniter is a small ceramic or metal component that creates a spark to light your burner flames. When you turn the burner dial and hear that clicking sound, you're activating the igniter. It's one of the most frequently replaced parts on a gas stove—and for good reason. Over time, moisture builds up inside the igniter, corrosion forms on the electrode tips, and the ceramic insulation can crack from repeated heating and cooling cycles.
Learn About Paying Your FGUA Bill Online →
Most modern gas stoves use what's called a "spark igniter" system rather than standing pilot lights. This system is more efficient than older designs because it only creates a spark when you actually turn on the burner. However, this also means the igniter works harder and fails more often than you might expect. According to appliance repair data, igniters account for roughly 35-40% of all gas stove service calls. In many cases, homeowners replace them once every 3-5 years depending on usage patterns and kitchen humidity.
The igniter sits right under the burner grate, close to where the gas comes out. This location exposes it to spills, grease splatters, and moisture from cooking. When you boil a pot of water or make pasta, steam rises directly onto the igniter. Over months and years, this moisture corrodes the electrode and prevents proper spark generation. You'll notice the problem when you turn on a burner and hear lots of clicking—sometimes 30 seconds or more—before the gas finally lights, or the burner won't light at all.
Understanding where your igniter sits and why it fails helps you recognize when replacement is necessary and gives you confidence that this is a fixable problem. Most igniters cost between $15 and $75 in parts alone, making this one of the more affordable stove repairs you can tackle yourself.
Takeaway: Gas stove igniters fail regularly due to moisture and grease exposure. Excessive clicking or failure to light signals it's time to replace yours.
Before you touch anything on your stove, you need to understand the safety steps that protect you from gas leaks and electrical shock. Gas stoves carry two distinct hazards: natural gas or propane, and electrical current running through the igniter. Both require respect and careful preparation.
Free Guide to Pay by Plate Illinois Billing →
Start by turning off the gas supply to your stove. If your stove has a control valve at the back where the gas line connects, turn that valve parallel to the gas line (perpendicular means it's open, parallel means it's closed). If you can't locate this valve or it won't turn by hand, turn off the main gas supply to your house at the meter or wall connection. Many homeowners skip this step thinking they'll work quickly, but a single slip can force gas into your kitchen. Gas is odorless in its natural state—utility companies add mercaptan (that "rotten egg" smell) so you can detect leaks. If you smell gas while working, leave immediately and call your gas company's emergency line.
Next, turn off the electrical power to your stove at your home's circuit breaker. Even though the igniter operates on relatively low voltage, electricity can still cause serious burns or arrhythmia. Flip the breaker all the way off—you should see the switch move to a clear "off" position. Wait 5 minutes before proceeding. This allows any residual electrical charge to dissipate from the stove's ignition module.
Gather these tools before you start: a screwdriver set (both Phillips and flat-head), needle-nose pliers, a wire connector removal tool or small flathead screwdriver, flashlight or headlamp, and if possible, your stove's manual or a photo of the original igniter to match. You'll also want a small bowl or container to hold screws so they don't get lost.
Let your stove cool completely if you've used it recently. The burner grates, caps, and surrounding metal can remain hot for 30 minutes or longer after use. Touch the burner area with your hand from a distance before getting close—you should feel no heat radiating from it.
Takeaway: Shut off gas at the control valve and electrical power at the breaker before beginning any work. Gather your tools and allow the stove to cool completely.
With safety precautions in place, you can now access the igniter. The exact process varies slightly between stove models, but the general approach remains consistent across most brands including Whirlpool, GE, Frigidaire, LG, and Samsung.
Free Guide to Mold Removal Methods for Walls →
First, remove the burner grate and burner cap from the burner with the failed igniter. Most burner caps simply lift off. Some grates are held down by a single screw or clip—check underneath before pulling. Set these parts aside in a safe place. You now have a clear view into the burner area.
Look directly under the burner. You'll see the igniter—a small ceramic rod with a metal electrode at the tip, usually white or light gray in color. The igniter is typically held in place by one or two screws. Using your Phillips head screwdriver, carefully remove these screws. The igniter is fragile, so support it with your other hand as you remove the final screw so it doesn't drop.
Now look at the wire connector attached to the back of the igniter. This connector plugs into a wire coming from your stove's ignition module. There are several common connector types: a simple push-fit connector that slides off, a connector with a small clip you need to press before sliding, or a connector with a locking tab. Examine your connector carefully to determine which type you have. If it's a simple push-fit, gently wiggle and pull it straight out. If there's a clip or tab, press or flip it first, then pull. Don't yank on the wire itself—always hold the connector housing.
Once the wire is disconnected, you can fully remove the igniter. Inspect the hole where it sat. You'll likely see corrosion, grease buildup, or mineral deposits. Take your time to clean this area with a damp cloth or paper towel. Some people use a small brush to remove stubborn debris. This cleaning helps your new igniter make better contact with the stove and improves its performance.
Takeaway: Remove burner grate and cap, unscrew the igniter, disconnect the wire connector by identifying which type (push-fit, clip, or tab), then clean the igniter cavity.
Buying the right replacement is critical because igniters vary significantly between stove models. An igniter designed for a Whirlpool won't work in a Samsung, and even within the same brand, different models use different igniters. Installing the wrong part wastes money and leaves you without a working stove.
How to Delete Your Fitbit Account Guide →
Your stove's model number is your most reliable identification tool. This number appears on a metal label typically located inside your oven (check the side walls or back wall), behind the range, or sometimes on the back of the control panel. Write down the entire model number—it often looks like "WFG745H0FS" or similar. This number tells the parts supplier exactly which igniter you need.
If you can't locate the model number, take a clear photo of the failed igniter before discarding it. Photos should show the overall shape, the connector type, and any markings or numbers printed on the ceramic body. Some igniter manufacturers print part numbers directly on the ceramic or the connector housing.
Once you have the model number or photos, visit major online appliance parts retailers like Whirlpool Direct Parts, GE Appliances Parts, or third-party retailers like Sears Parts Direct, PartSelect, or AppliancePartsPros.com. Type your stove's model number into their search field. The website will show you the specific igniter for your stove, complete with a photo and part number.
Igniters range from $15 for basic aftermarket models to $75 for OEM (original equipment manufacturer) parts. OEM parts are manufactured by your stove's original maker or under license. Aftermarket parts are made by independent manufacturers but must
This guide is for general information only and is not medical, financial, legal, or other professional advice. For decisions specific to your situation, consult a qualified professional. See our Editorial Policy.