Your Subaru key fob is one of those devices you use dozens of times a week without thinking about it—until it stops working. The battery inside is responsible for powering the remote signals that lock and unlock your doors, open your trunk, and sometimes activate your panic alarm. Like any battery, it depletes over time through normal use.
Learn About Paying Your FGUA Bill Online →
Most Subaru key fob batteries last between three and four years, depending on how frequently you use the fob. Every time you press a button, your fob sends out a radio frequency signal to your vehicle's receiver. While these signals use minimal power, the cumulative effect of thousands of button presses adds up. Additionally, extreme temperatures—both hot and cold—can accelerate battery drain. If you live in a climate with harsh winters or blistering summers, you might notice your battery depletes faster than the average timeline.
You'll notice several warning signs before your fob dies completely. The first signal is usually decreased range: you'll need to stand closer to your Subaru for the fob to work. Next, you might find that buttons respond inconsistently—sometimes they work, sometimes they don't. Finally, one button may fail while others still function. These patterns indicate the battery is nearing the end of its life.
The good news is that replacing a Subaru key fob battery is a task you can handle yourself in under five minutes. You don't need special tools or technical knowledge. Understanding how and why this process works makes it less mysterious and more straightforward. Most Subaru fobs use the same type of battery across their model lineup, making replacement predictable and inexpensive.
Takeaway: Battery failure in Subaru key fobs is normal wear and tear, not a sign something is wrong with your vehicle. Recognizing early warning signs like reduced range or inconsistent button response helps you replace the battery before complete failure.
Subaru key fobs typically use one of two battery types: CR2032 or CR2025. These are both lithium coin cell batteries, and they look nearly identical to the untrained eye. The difference lies in their thickness: CR2032 batteries are 3.2 millimeters thick, while CR2025 batteries are 2.5 millimeters thick. This small difference matters because putting the wrong battery in your fob can create connection problems or prevent the case from closing properly.
Free Guide to Pay by Plate Illinois Billing →
The easiest way to determine which battery your Subaru needs is to check your owner's manual. Your manual includes specific information about your vehicle's key fob battery type, usually in the section covering remote keyless entry or key fob maintenance. If you don't have a physical copy, most Subaru manuals are available online through the official Subaru website or through automotive documentation sites. You can also visit a Subaru dealership parts department—they can tell you the correct battery type within seconds.
If you've already opened your old fob and removed the depleted battery, you can simply take it with you to any pharmacy, electronics store, or supermarket that sells batteries. Show the old battery to a store employee and they can match it for you. This approach eliminates guesswork and ensures you purchase the correct replacement.
You'll find CR2032 batteries are far more common than CR2025 batteries, so stock is typically available at major retailers. A single replacement battery costs between $3 and $8, depending on the brand and retailer. Name brands like Panasonic, Energizer, and Sony are widely available. Store brands are also reliable and often cost less. Avoid purchasing batteries from unclear sellers or extremely discounted sources, as battery quality varies and a poor-quality battery may fail sooner than expected.
Some people buy extra batteries while they're at the store to keep on hand for future replacements. This is a practical approach, since coin cell batteries remain functional for several years when stored in cool, dry conditions. Having a replacement ready means you won't be stranded if your key fob fails unexpectedly.
Takeaway: Verify your battery type through your owner's manual or by contacting your Subaru dealer. A CR2032 is the most common choice for Subaru fobs, but confirming this takes only minutes and prevents purchasing the wrong battery.
The physical design of Subaru key fobs makes opening them straightforward, but you need to know where to apply pressure. Most Subaru fobs have a small slot or seam running around the edge where the case separates into two halves. You're looking for the line that runs vertically down one side of the fob, typically between the buttons and the back edge. This seam is where you'll insert a tool to pry the case apart.
Free Guide to Mold Removal Methods for Walls →
A standard flathead screwdriver works well for this task, but a coin also does the job effectively. Many people keep a butter knife or plastic spoon in their pocket during this process as an alternative. The key is using something thin enough to fit in the seam without requiring excessive force. You want to apply steady, gradual pressure rather than jamming the tool in aggressively. Aggressive prying can crack the plastic case or damage the internal circuitry.
Position your tool at the seam and gently twist or lever it back and forth. You'll feel slight resistance as the two plastic halves begin to separate. Work slowly around the perimeter of the fob if one spot doesn't immediately release. Some fobs have tighter seams than others, and distributing pressure around the case prevents damage to any single spot. Within thirty seconds to a minute, the two halves will separate enough for you to pull them apart by hand.
Once the case is open, you'll see the internal circuitry and the battery sitting in a small compartment. The battery is usually held in place by a metal contact spring on one or both sides. This is important to understand for the next step. The orientation of the battery matters—it needs to sit properly against these metal contacts to complete the electrical circuit.
Set the two case halves aside on a clean surface where you won't lose small pieces. Some fobs have tiny springs or gaskets, and losing these components means your fob won't function correctly after reassembly. A small dish or paper towel works well for containing these small parts during the process.
Takeaway: Find the seam running around the edge of your fob and apply gentle, steady pressure with a thin tool to separate the two halves. Working slowly prevents damage and keeps all internal components intact.
With your fob case open, you'll see the old battery sitting in its compartment. The battery is typically a shiny silver coin-shaped object, usually with some dust or discoloration from years of use. It sits in a small plastic holder or simply rests against metal contact springs. Some batteries lift out easily, while others have a small plastic tab attached that you can pull gently to dislodge them.
How to Delete Your Fitbit Account Guide →
If the battery doesn't lift out with gentle upward pressure, look around its edges for a small tab or loop of plastic. This tab is designed specifically for battery removal—gently pulling it lifts the battery from its seat. If no tab is visible, the battery likely rests between two metal springs or contacts. In this case, apply light upward pressure with your fingernail or the edge of a coin until the battery pops free. The spring tension is mild and the battery will release with minimal effort.
Once the old battery is removed, inspect the interior of the fob briefly. Look for any corrosion around the battery compartment—white, blue, or greenish residue indicates the old battery may have begun leaking. This is rare but worth noting. If significant corrosion is present, you can gently clean the compartment with a cotton swab, though in most cases the fob will function fine without cleaning.
Before inserting your new battery, check its orientation. Coin cell batteries have a positive side (marked with a plus sign or simply labeled) and a negative side. The positive side typically faces outward, but confirm this by looking at the inside of your fob case. You'll usually see a tiny plus or minus mark indicating which side should face up. Match the new battery's orientation to this marking.
Insert the new battery with the correct side facing up, pressing gently until it sits flush in the compartment. You
This guide is for general information only and is not medical, financial, legal, or other professional advice. For decisions specific to your situation, consult a qualified professional. See our Editorial Policy.