A relay is an electromagnetic switch found in cars, trucks, appliances, and industrial equipment. Its job is simple but critical: it uses a small electrical signal to control a much larger electrical current. Think of it like a light switch, except instead of your finger flipping it, an electromagnet does the work. When power flows through a coil inside the relay, it creates a magnetic field that pulls a metal arm, which then closes contacts and allows a bigger current to flow through a separate circuit.
Learn About Paying Your FGUA Bill Online →
Relays appear in surprising places. Your car uses them to control everything from the starter motor to the headlights and fuel pump. Refrigerators, air conditioners, and washing machines all rely on them. Industrial equipment uses relays to manage heavy machinery and safety systems. A single relay failure can mean your car won't start, your headlights flicker unpredictably, or an entire machine stops working.
Testing a relay with a multimeter matters because it tells you whether the relay's electromagnet is functioning, whether its contacts are opening and closing properly, and whether electrical continuity exists where it should. Rather than guessing whether a relay is bad—which costs money if you replace a working part—you can measure its actual performance. A multimeter gives you concrete resistance and continuity readings that show what's really happening inside the relay.
Most relay failures fall into two categories: the electromagnet coil stops working (usually due to a break in the wire), or the contacts become pitted, corroded, or stuck (meaning they can't make good electrical contact). Testing reveals which problem you're facing. This knowledge helps you decide whether to replace the relay, clean the contacts, or look for a different problem entirely.
Practical takeaway: Before spending money on a new relay, understanding how to test one saves both time and expense. You'll know for certain whether the relay itself is the problem or whether something else needs attention.
A digital multimeter is your primary tool for relay testing. You don't need an expensive model—a basic multimeter with continuity testing capability and resistance measurement (ohms) costs between $10 and $25 and handles relay testing perfectly. Look for models with clear display screens and labeled dials or buttons. Popular entry-level options include the Craftsman Digital Multimeter, Southwire Digital Multimeter, and Fluke models in the 110 or 115 series.
Free Guide to Pay by Plate Illinois Billing →
Before you begin testing, familiarize yourself with three essential multimeter settings: continuity mode, resistance mode (measured in ohms), and voltage mode. Most multimeters display continuity testing with a symbol that looks like a sound wave or a small arrow. Resistance mode is typically labeled with the Greek letter omega (Ω). Voltage mode shows V with either AC or DC indicators. For relay testing, you'll primarily use continuity and resistance modes.
The multimeter works by sending a tiny test current through whatever you're testing and measuring how much resistance it encounters. A relay coil typically shows resistance between 50 and 150 ohms, though this varies by relay type. Contacts that are working properly show zero or near-zero resistance (full continuity). Broken coils or corroded contacts show infinite resistance or no continuity at all—that's when you know there's a problem.
Before testing a relay, disconnect it completely from any power source or circuit. Testing a live relay can damage your multimeter or injure you. Take time to read your specific multimeter's manual, as button and dial placement varies between models. Some multimeters require you to plug the black probe into a "COM" port and the red probe into a voltage or resistance port. Others have different configurations.
Practical takeaway: Spend 10 minutes learning your multimeter's basic modes and probe setup. This foundation prevents mistakes and makes the actual relay testing straightforward.
The relay coil is the electromagnet that makes the relay work. When you apply voltage to the coil, it creates a magnetic field. If the coil is broken—which means the wire inside it has a gap or fracture—no magnetic field forms and the relay won't function. Testing the coil reveals this problem immediately.
Free Guide to Mold Removal Methods for Walls →
To test coil continuity, first identify the two terminals that connect to the coil. On most relays, these two terminals are separate from the others and labeled on the relay body or in documentation. Remove the relay from its socket or disconnect any wires attached to it. Set your multimeter to continuity mode.
Place one probe on each coil terminal. If the coil is good, you'll hear a beeping sound (most multimeters beep to indicate continuity) and the display shows "0" or very close to it, meaning the circuit is complete. If you hear no beep and the display shows "1" or "∞" (infinity symbol), the coil is broken and the relay needs replacement.
After testing continuity, switch your multimeter to resistance mode and test the same two coil terminals again. Note the reading. A working relay coil typically shows between 50 and 150 ohms of resistance, though some specialized relays may vary. If the resistance is extremely high (several thousand ohms or showing infinity), or extremely low (close to zero), the coil is damaged. Record this number for your records—it helps you verify you're testing the same relay type if you need to replace it.
Common findings during coil testing: A good coil shows continuity (beep) and resistance in the normal range. A burned coil shows continuity but resistance that's too high. A broken coil shows no continuity and infinite resistance. A shorted coil shows continuity but nearly zero resistance.
Practical takeaway: Always test coil continuity first. If it fails this test, the relay is definitely bad. If it passes, move on to testing the contacts.
The relay contacts are the metal pieces that actually open and close to switch the larger electrical circuit on and off. Unlike the coil, which should always have the same resistance, the contacts change their electrical state depending on whether the relay is energized. Testing contacts requires understanding this behavior and having a way to energize the relay during your test.
How to Delete Your Fitbit Account Guide →
Most relays have four to eight contact terminals. These are typically separated from the coil terminals and organized into groups. A common relay design has one set of "normally open" (NO) contacts and one set of "normally closed" (NC) contacts. Normally open contacts don't touch when the relay is unpowered—they only touch when the electromagnet is energized. Normally closed contacts touch when the relay is unpowered and separate when energized. Your relay documentation or the relay body itself usually marks these terminals.
To test contacts without energizing the relay, set your multimeter to continuity mode. Test between the two terminals of the normally open contacts. With the relay unpowered, you should hear no beep and see infinite resistance (the display shows "1" or "∞"). This confirms the contacts are open as they should be. Now test the normally closed contacts. You should hear a beep and see continuity or very low resistance, confirming they're closed.
If your normally open contacts show continuity when they shouldn't, or your normally closed contacts show no continuity when they should, the contacts are stuck. Stuck-open contacts won't let the circuit work even if the relay is energized. Stuck-closed contacts won't allow the circuit to turn off. Either problem means relay replacement.
For a complete contact test with the relay energized, you'll need a separate power source (usually 12V or whatever voltage the relay is rated for). This step is more advanced but reveals whether the relay actually switches when powered. Connect the coil terminals to power while testing the contacts—you should see the contact state flip. If the state doesn't change despite proper coil voltage, the relay's internal mechanism is damaged.
Practical takeaway: Contact testing starts with verifying the normal state (open or closed) of unpowered contacts. If they're already in the wrong state, the relay is failed and replacement is necessary.
After testing, you'll have several pieces of information: coil continuity (beep or no beep), coil resistance (a specific number in
This guide is for general information only and is not medical, financial, legal, or other professional advice. For decisions specific to your situation, consult a qualified professional. See our Editorial Policy.