Your garage door springs are among the most powerful components in your home. They support the full weight of a typical garage door—which ranges from 300 to 500 pounds—and work in tension to make opening and closing possible. When something goes wrong with a spring, the consequences can be serious. An improperly sized replacement spring won't support the door correctly, leading to uneven movement, strain on the opener motor, or worse, a door that won't stay open.
Learn About Paying Your FGUA Bill Online →
Measuring springs correctly is the foundation of any spring replacement or repair decision. This measurement tells you several critical facts: the exact type of spring you have, its load capacity, and whether a replacement will actually work with your specific door system. Many people skip this step and buy springs based on guessing or incomplete information, which leads to wasted money and potential safety problems.
Spring measurements also help you communicate accurately with suppliers or technicians. Rather than describing your door as "heavy" or "old," you'll have concrete numbers. This prevents miscommunication and ensures you get parts that actually match your setup.
There's another reason measuring matters: your existing springs give you the blueprint for what works. If your current springs have been handling your door safely for years, their measurements tell you exactly what to replace them with. You're not guessing—you're following proven specs.
Practical takeaway: Take measurements before shopping for springs. Having these numbers on hand prevents ordering the wrong part and gives you confidence in any repair decision you make.
Garage doors use two fundamentally different spring systems, and they measure differently. The first type is the torsion spring, which sits horizontally above the garage door opening, mounted on a shaft. The second is the extension spring, which runs along each side of the door opening and stretches as the door moves. Your door almost certainly uses one of these systems, and identifying which one is your first measurement task.
Free Guide to Pay by Plate Illinois Billing →
Torsion springs are measured by three key numbers: wire diameter, inner diameter, and length. The wire diameter tells you how thick the metal coil is—measurements typically range from 0.177 inches to 0.283 inches. The inner diameter is how wide the coil itself is when measured from the inside edge of the wire on one side to the inside edge on the opposite side. This usually falls between 1.5 and 2.5 inches. The length is straightforward—how long the spring is from end to end, typically between 20 and 35 inches.
Extension springs use different measurements. These springs have end loops or hooks, and you need to measure the wire diameter, the spring diameter (outside measurement across the coil), and the length of the spring body itself—not including the loops. Extension springs sit vertically, so their length measurements are often longer, sometimes reaching 50 inches or more.
The load rating is another critical measurement for both types. This number tells you how much weight the spring can support. It's measured in "turns"—the number of complete rotations the spring makes when coiled. A spring with 200 turns can handle a different door weight than one with 250 turns. This specification is often stamped on the spring itself or on a label near the spring.
Practical takeaway: Photograph your spring setup from multiple angles before you start measuring. Being able to identify whether you have torsion or extension springs prevents measurement errors and saves time.
Torsion springs sit horizontally above your garage door, mounted to a shaft that runs across the width of the door opening. To measure one properly, you'll need a tape measure, calipers or a dial indicator for precise measurements, and ideally a notepad to record everything.
Free Guide to Mold Removal Methods for Walls →
Start by taking a clear photo of the spring from directly above, showing how it sits on the shaft. This becomes your reference image. Next, locate where the spring begins and ends on the shaft. Torsion springs often have specific mounting points, and knowing these locations matters for ordering a replacement.
For the wire diameter, use calipers if you have them—they give you the most accurate measurement. If you only have a tape measure, measure across the wire at its thickest point. Write down this number to the nearest 0.01 inch. Common wire diameters are 0.177, 0.207, 0.225, 0.236, 0.250, 0.263, and 0.283 inches. Your measurement will likely be close to one of these standard sizes.
The inner diameter requires measuring across the inside of the coil. Place your tape measure or calipers at the inner edge of the wire on one side and measure straight across to the inner edge on the opposite side. This gives you the inner diameter. Record this to the nearest 0.05 inch. Most torsion springs have inner diameters between 1.5 and 2.5 inches.
For the length, measure from one end of the spring to the other. On a torsion spring, this measurement typically ranges from 20 to 35 inches. Measure carefully from the very end of one side to the very end of the other side, following along the coil. If the spring has mounting brackets at the ends, measure to the outer edge of these brackets, not to the inner edge of the spring itself.
Finally, look for the turns specification. Many springs have this number stamped, printed, or etched somewhere on the coil or on a nearby label. The turns number might look like "200 T" or "250 T" and tells you the spring's load capacity. If you can't find it stamped on the spring, note that you couldn't locate this specification—a supplier can sometimes help you determine it from your other measurements.
Practical takeaway: Document everything by writing your measurements down immediately and taking clear photos. The three essential torsion spring numbers are wire diameter, inner diameter, and length. The turns specification is equally important but sometimes harder to locate.
Extension springs are simpler to measure than torsion springs because they're more accessible and their parts are clearer. These springs run vertically along each side of the garage door opening and stretch as your door opens. You'll notice them more easily than torsion springs because they're out in the open, not hidden above the door.
How to Delete Your Fitbit Account Guide →
Before touching anything, take a photograph of one extension spring in place. This shows you the mounting points and how the spring is positioned. Extension springs have end fittings—these might be open hooks, closed loops, or eyebolt connections. Photograph these fittings closely because their type is part of your spring specification.
Start measuring the wire diameter using calipers if possible. This is the thickness of the wire the spring is made from. If you're using a tape measure, wrap it around the wire and divide by 3.14 to get the diameter. Common extension spring wire diameters range from 0.148 to 0.250 inches. Record your measurement to the nearest 0.01 inch.
Next, measure the outside diameter of the coil itself—this is different from the inner diameter used for torsion springs. Measure across the spring from the outer edge of the wire on one side to the outer edge of the wire on the opposite side. This measurement typically ranges from 1.5 to 2 inches for most residential garage door springs.
For the spring length, measure only the body of the spring, not including the end loops or fittings. Start your measurement at the beginning of the first coil and end at the beginning of the last coil. This can be tricky because the end loops extend beyond the main coil body. Many extension springs measure between 30 and 60 inches in body length.
Identify the end fittings type. Are both ends open hooks? Are they closed loops? Does one end have an eyebolt connection? Write down exactly what you see. The fitting type is part of your spring specification and affects whether a replacement will fit your existing hardware.
Finally, look for the load rating. This might be stamped on the spring body or on the end loops. You're looking for a number like "100" or "125" which represents the spring's pound rating—how much weight it can handle. If you find multiple springs on your door (many setups have
This guide is for general information only and is not medical, financial, legal, or other professional advice. For decisions specific to your situation, consult a qualified professional. See our Editorial Policy.