A stripped screw is one of those frustrating moments where the screw just spins in the hole without tightening or loosening. To understand why this happens, you need to picture what's going on inside the material. When you drive a screw into wood, plastic, or metal, the threads cut into the surface and create a grip. That grip is what holds the screw tight. When those threads get damaged or worn away, the screw loses its purchase—it's like trying to climb a rope that's been worn smooth.
Learn About Paying Your FGUA Bill Online →
The most common cause is using the wrong size screwdriver or drill bit. If your bit is too small or too large, it doesn't fit snugly into the screw head. This means the driver can slip out of the grooves, and when that slipping happens repeatedly, it rounds out the screw head. The edges that the driver grips become smooth and useless. In wood, over-tightening is another major culprit. Wood fibers compress and break down around the screw hole, especially in softer woods like pine or cedar. The material essentially crushes, leaving nothing for the threads to grip.
Material matters too. Plastic is especially prone to stripping because it's softer and more forgiving than wood or metal. A screw can chew right through the plastic threads if driven too quickly or too forcefully. Metal fasteners have better resistance, but they still strip if you use incorrect tools or apply excessive force. Even the age of the screw plays a role—older, lower-quality screws have less precise threading and strip more easily than modern hardware-grade fasteners.
Practical takeaway: Stripped screws happen because tools slip or the surrounding material gets damaged. Understanding the cause in your specific situation helps you choose the right repair method. Take a moment to examine whether the problem is the screw head itself or the hole it sits in—this distinction shapes your next steps.
Before you invest time in a repair, confirm that you're actually dealing with a stripped screw. This matters because the solution changes depending on what's wrong. A screw that's simply stuck or corroded behaves differently than a stripped one, and treating them the same way wastes effort.
Free Guide to Pay by Plate Illinois Billing →
Start by trying to remove the screw with the correct tool. Use a screwdriver or drill bit that fits the screw head precisely—not a close approximation, but an exact fit. If a properly-fitting driver still spins without catching, and you can feel it slipping rather than gripping, you likely have a stripped screw head. However, if the driver catches but the screw simply won't turn, the issue might be corrosion, paint, or the screw being over-tightened rather than stripped. In this case, apply penetrating oil, wait 15-30 minutes, and try again with steady pressure.
Another diagnostic test: Can you feel resistance when you turn the screw, or is it completely free-spinning? True stripping creates zero resistance—the screw turns without any mechanical connection. You might hear a grinding sound as well, which indicates the driver is skidding across worn metal or plastic. If there's still some resistance, the hole or threads may just need cleaning or lubrication rather than repair.
Look at the screw head directly if it's accessible. Visible damage—like rounded corners, chipped edges, or deep scratches from repeated slipping—confirms that the head is stripped. The holes or grooves in the head should have sharp, clean edges. Rounded, smoothed edges mean the driver has been bouncing around inside them.
Also consider where the problem is. Is it the screw head (where the driver fits) or the hole itself (where the screw sits)? You can have a perfectly good screw head in a stripped hole, or a damaged screw head in a perfectly good hole. Testing both independently helps you understand what actually needs fixing. If you can remove the screw with your current tools, the hole is likely the issue. If the screw won't budge and your driver slips, the head is the problem.
Practical takeaway: Spend two minutes diagnosing the problem correctly. Use the right-sized tool, test for resistance and slipping, and look closely at what's damaged. This takes guesswork out of choosing a repair method.
Once you've confirmed the screw is stripped, your next challenge is getting it out. A stripped screw won't cooperate with normal removal techniques, so you need tactics designed specifically for when the driver no longer grips the head.
Free Guide to Mold Removal Methods for Walls →
The rubber band method works surprisingly often for slightly stripped screws, especially if the head is only partially damaged. Place a wide rubber band flat over the stripped screw head, press your screwdriver firmly through the rubber into the screw, and turn slowly. The rubber fills tiny gaps and creates friction between the driver and the worn head. This works best for screws that aren't over-tightened and for head damage that's minor. It takes patience—turning too quickly just shreds the rubber without accomplishing anything.
A screw extractor is a specialized tool made exactly for this situation. These look like drill bits but have reverse threads. You drill a small hole into the center of the stripped screw, insert the extractor, and as you turn it counterclockwise, the reverse threads dig in and pull the screw out. Screw extractors come in sets with multiple sizes, and they're inexpensive—typically $10 to $25 for a set. They work on metal, plastic, and wood equally well. The technique requires a steady hand and a drill, but the success rate is high when the screw head is above the surface.
Pliers or vice-grips can work if enough of the screw head protrudes above the surface. Clamp the pliers tightly onto the screw head's sides, then turn counterclockwise with steady, firm pressure. This works best on larger screws and doesn't work at all if the head is flush with or recessed into the surrounding material. The danger here is that you might damage the material around the screw while applying the necessary pressure.
For screws embedded in wood, drilling out the entire screw is sometimes the quickest option. Use a drill bit slightly smaller than the screw's shaft diameter and drill straight through the screw. This destroys the screw but leaves the hole intact for repair. You'll then need to fill the hole if you plan to use the same location again.
If the screw is in metal or has been severely over-tightened, penetrating oil can help before attempting any removal. Apply it around the screw head, let it soak for several hours (or overnight), then try removal again. The oil reduces friction and sometimes loosens the bond between the screw and surrounding material just enough to make removal possible.
Practical takeaway: You have multiple removal options depending on how accessible the screw head is and what material it's in. Start with the simplest method (rubber band), move to extractors if that fails, and drill out as a last resort. Each method trades off speed for success rate.
After removing the stripped screw, you're left with a hole that can't grip a new screw properly. This hole needs restoration before you can reinstall a fastener. The method depends entirely on what material the hole is in.
How to Delete Your Fitbit Account Guide →
In wood, the classic solution is a wooden toothpick or wooden dowel. Break a toothpick to fit the hole, apply wood glue to it, and tap it into the stripped hole. Let the glue dry completely (usually 24 hours), then trim the toothpick flush with the surface. The wood grain of the toothpick provides new material for the screw to grip. You can then drive a screw into the same hole—the toothpick provides fresh wood fibers and threads. This method costs almost nothing and works well for small holes in softwood. For larger holes or hardwood, use a wooden dowel of appropriate diameter instead of a toothpick. The principle is identical but works for bigger fasteners.
Another wood option is epoxy wood filler. Mix two-part epoxy according to package directions, pack it tightly into the hole, and smooth it level with the surface. Once cured (typically 24 hours), you can drill a new hole in the hardened
This guide is for general information only and is not medical, financial, legal, or other professional advice. For decisions specific to your situation, consult a qualified professional. See our Editorial Policy.