A factory reset returns your Roomba to its original settings, removing all personalized configurations, maps, and connection data. This isn't something you'll need to do often, but certain situations make it the right solution. If your vacuum stops responding to commands through the app, won't connect to your Wi-Fi network after multiple attempts, or behaves erratically during cleaning cycles, a factory reset can clear out corrupted settings that are causing the problems.
Learn About Paying Your FGUA Bill Online →
Sometimes a Roomba develops glitches after a software update goes wrong, or if you've had multiple connection failures while traveling or moving to a new location. If you're planning to give your Roomba to someone else or sell it, a factory reset removes all your personal information, Wi-Fi credentials, and account connections from the device. This is particularly important for protecting your home network details and ensuring the next owner starts with a clean slate.
Another common reason involves the vacuum's navigation system. If your Roomba repeatedly gets stuck in certain areas, fails to recognize room boundaries you've set, or creates incomplete maps despite multiple cleaning sessions, a reset can help recalibrate its sensors and mapping behavior. Some owners also perform resets when troubleshooting persistent error codes that don't respond to standard fixes like charging contacts cleaning or wheel inspection.
Understanding when to reset versus when to try other troubleshooting steps matters. Before resetting, check whether the issue stems from something simpler—like a full dustbin, stuck brush, or Wi-Fi interference from nearby electronics. A reset is more invasive than these basic fixes, so it makes sense as a later troubleshooting step rather than a first response.
Practical takeaway: Determine whether your Roomba's issue actually requires a factory reset or if standard maintenance might solve the problem. Document any error codes or specific behaviors you're seeing—this information helps you decide if a reset is necessary.
iRobot manufactures several Roomba lines, and reset procedures vary depending on your model generation. The newer models (Roomba s9+, j7+, and i series) feature more advanced connectivity and different button configurations than older versions like the Roomba 690, 800, or 900 series. Checking your specific model number before attempting a reset prevents you from trying the wrong procedure, which could cause confusion or temporary freezing of the robot.
Free Guide to Pay by Plate Illinois Billing →
For most newer Roomba models, the reset button is a small recessed button located on the underside of the unit or near the charging contacts. You'll typically need a thin object like a paperclip or pen to press it for a specific duration. Older mechanical dial-based models sometimes use different reset methods involving button combinations or longer press-and-hold sequences. The model number appears on a sticker underneath the bumper or on the side of the dustbin, usually starting with numbers like 675, 960, or j715.
Some higher-end models now allow resets through the iRobot app itself, making the process more straightforward for users who prefer not to access the underside of the unit. This app-based reset is typically labeled as "Forget Robot" or "Reset to Factory Settings" in the settings menu. Other models require both a physical reset button press and confirmation through the app to fully complete the factory reset process.
If you're unsure which method applies to your model, the product manual that came with your vacuum contains specific instructions. You can also find model-specific guides on the iRobot website or by entering your model number on their support page. Taking a photo of your model number before you start makes it easy to reference instructions if you need to pause and look something up during the process.
Practical takeaway: Locate your Roomba's model number and verify the correct reset procedure for that specific version before attempting anything. This one step prevents mistakes that could require customer support intervention.
The physical reset procedure for most mid-range and older Roomba models follows a consistent pattern, though timing and button location vary. Start by ensuring your Roomba is powered off and not charging. If it's currently docked, remove it from the dock. This prevents any automated responses or charging interference during the reset. Place the vacuum on a flat surface where you can easily access the underside without tipping it over.
Free Guide to Mold Removal Methods for Walls →
Flip the Roomba over or position it so you can see the underside clearly. Look for the reset button—it's typically a small, recessed circular button, sometimes labeled "RESET" or shown in your manual. Gather a thin tool like an unfilled ballpoint pen, straightened paperclip, or the special reset tool if it came with your manual. Press and hold this button for the duration specified in your model's instructions, which is usually between 10 to 15 seconds. You'll feel slight resistance as you press.
While holding the button, watch for indicator lights or sounds from the unit. Some Roomba models emit a beeping sound or flash their indicator lights to confirm the reset is processing. Continue holding for the full duration even if lights flash before the timer ends—releasing too early may not fully clear the device settings. After the specified time passes, release the button and flip the Roomba upright again.
Turn on the Roomba using its power button or dock it for a brief moment, then remove it again. The vacuum may take 30 seconds to a few minutes to boot up after a reset. During this time, it might cycle through startup sounds or light patterns different from its normal startup. This is normal behavior following a factory reset. Once it's fully powered and quiet, your Roomba has completed the physical reset and returned to its original factory configuration.
Practical takeaway: Follow the timing requirements exactly—too short a press won't complete the reset, while the process is generally forgiving of holding the button slightly longer. Write down or set a phone timer to ensure you hit the correct duration.
If your Roomba model supports the iRobot app, you may be able to initiate a factory reset through your phone or tablet without needing to access the physical reset button. This method works best for newer models that maintain app connectivity even when experiencing other issues. Open the iRobot app on your device and navigate to the settings section for your specific robot. Look for options labeled "Forget Robot," "Reset to Factory Settings," "Restart Robot," or "Remove Device."
How to Delete Your Fitbit Account Guide →
Before selecting a reset option, understand what each choice does. A "Restart Robot" or "Reboot" option simply reboots the device—it clears temporary glitches without erasing settings or Wi-Fi connections. A "Forget Robot" or "Reset to Factory Settings" option removes all customizations, maps, Wi-Fi credentials, and account associations. If your Roomba is simply frozen or unresponsive, try a simple restart first. If it's not connecting to your Wi-Fi or you're preparing to transfer it to another account, then select the full factory reset option.
When you select a factory reset through the app, the system typically asks for confirmation because this action cannot be easily undone without manually reconfiguring the device. You may see a warning stating that all maps, schedules, and Wi-Fi settings will be removed. Confirm that you want to proceed. The app will then send the reset command to your Roomba. The vacuum may disconnect from the app immediately, and you'll see a message indicating the reset is in progress.
Once the reset completes, the Roomba will appear offline in your app. This is expected—it no longer has the Wi-Fi connection information stored. You'll then need to set up the robot again as if it were brand new, including reconnecting it to your Wi-Fi network through the initial setup process. The advantage of app-based resets is that they're faster and don't require physical access to small buttons, making them practical for people with limited dexterity or those who find the device difficult to flip over.
Practical takeaway: If your Roomba is still connecting to your app, try a simple restart first. Reserve the full factory reset option for situations where reconnection or basic troubleshooting hasn't resolved the issue.
Right after your Roomba completes a factory reset, it will behave as though it's brand new from the box. All previous settings vanish
This guide is for general information only and is not medical, financial, legal, or other professional advice. For decisions specific to your situation, consult a qualified professional. See our Editorial Policy.