Learn How to Clean Your Samsung Washer Filter

Understanding Your Samsung Washer Filter System

Samsung washing machines contain a filter system designed to catch debris, lint, coins, and other objects that may enter the drum during the wash cycle. Understanding how this filter works is the first step toward proper maintenance. Most Samsung washers have two types of filters: the inlet valve filters that screen water coming into the machine, and the drain filter (also called a drain pump filter) that prevents debris from clogging the drain pump and hose.

Learn How To Guide for Beginners →

The drain filter is the component most homeowners need to clean regularly. This filter sits at the bottom of your washer, typically behind a small panel on the front of the machine. As water drains from each wash cycle, small particles collect in this filter. If the filter becomes too clogged, water may drain slowly, or your washer may display error codes indicating a drainage problem. Samsung's design allows water to pass through while trapping solid materials.

The inlet valve filters are smaller screens located where the water supply hoses connect to the back of your machine. These filters prevent sediment and mineral deposits from entering the washing drum and damaging the valve mechanisms. While less frequently accessed than drain filters, inlet filters should be inspected during annual maintenance.

Different Samsung washer models may have slightly different filter locations and access points. Front-load models typically have the drain filter accessible from the front bottom, while some top-load models may position filters differently. Checking your specific model's manual will confirm the exact location and design of your machine's filter system.

Practical Takeaway: Before attempting to clean your filter, locate where it sits in your specific washer model by checking your owner's manual or the manufacturer's website for your model number.

Gathering Tools and Preparing Your Washer

Cleaning your Samsung washer filter requires minimal tools, most of which you likely already have at home. Gather a small bucket or container to catch water that will drain from the filter area. A soft-bristled brush or old toothbrush works well for scrubbing debris from the filter mesh. You may want a flashlight to see inside the filter compartment clearly. Have several clean towels available to absorb water that spills during the cleaning process, and wear clothes you don't mind getting wet.

Learn How to Make an Insurance Claim Step by Step →

Before you begin, turn off your washer and ensure it is not in the middle of a cycle. Unplug the machine from the electrical outlet for safety. Even though you are only accessing the filter area, electrical safety is important when working with any household appliance. Allow the washer to sit for a few minutes if it has just finished a cycle, as water inside may still be warm or hot.

If your washer has a drain filter access panel, you may need to remove a decorative cover first. Some models use a simple pull-down panel, while others may have a small door held by a latch. Check your manual for the specific method for your model. Place your bucket directly under the filter access point before opening anything, as water will drip out.

Preparation also includes clearing the area around your washer so you have room to work comfortably. You may need to crouch or kneel, so ensure the floor space is accessible. If your washer is in a laundry room with carpeting, place extra towels under and around the work area to protect the floor from water damage.

Practical Takeaway: Lay out all your supplies before you begin, position your bucket and towels, and always unplug your washer before accessing internal components.

Removing and Accessing the Drain Filter

Most Samsung front-load washers have a drain filter located at the bottom front of the machine, behind a small access panel. This panel is typically held in place by a simple plastic latch or clip. Gently pull the panel downward or press the latch to release it. The panel should come away from the machine easily without force. If it seems stuck, double-check that you are releasing any latches properly rather than pulling harder.

Get Your Free Guide to Continuing Care Retirement Communities →

Once the panel is open, you will see the drain filter, which looks like a cylinder about three to four inches long. The filter has a handle or knob on the end facing outward. You may also see a small drain plug nearby, which is a separate component used to manually drain water from the washer if needed. Position your bucket to catch water before proceeding.

To remove the filter, grasp the handle firmly and turn it counterclockwise about a quarter turn. The filter should then pull straight out toward you. Water may drip from the opening, which is normal. Continue holding the filter over your bucket as you completely remove it. Some models have a rubber gasket or seal around the filter; ensure this stays attached to the filter itself rather than remaining in the machine.

If the filter is difficult to turn, it may be stuck due to lint buildup or mineral deposits. Do not force it excessively, as you could break the handle. Instead, try gently rocking it back and forth while turning. If it still will not budge, allow the washer to sit unplugged for 15 to 20 minutes, then try again. Stubborn filters sometimes release after a brief waiting period.

Practical Takeaway: The drain filter removes by turning counterclockwise and pulling straight out; take your time and do not use excessive force if resistance is encountered.

Cleaning the Filter Thoroughly

With the filter removed, hold it over your bucket and rinse it under warm running water. This initial rinse removes loose lint and debris accumulated from recent wash cycles. You will likely see a surprising amount of material come out during this first rinse—this is completely normal and shows why regular filter cleaning matters. Continue rinsing until the water running through the filter runs relatively clear.

Free Guide to Dental Implant Trial Programs in Baton Rouge →

After the initial rinse, use your soft-bristled brush to gently scrub the outside mesh of the filter. Work the brush back and forth across the mesh surface in different directions to dislodge trapped particles. The brush bristles should be soft enough not to damage the mesh openings. Pay particular attention to any areas where debris appears stubborn or packed in. A toothbrush works well for reaching the edges and ridged areas of the filter.

For filters with significant mineral deposits or stubborn buildup, soak the filter in warm water mixed with equal parts white vinegar for 30 minutes to one hour. The mild acidity of vinegar breaks down mineral deposits without damaging the filter material. After soaking, rinse the filter thoroughly and brush it again to remove the loosened deposits. Some homeowners prefer using a mixture of baking soda and water for particularly dirty filters, which also works effectively.

Inspect the filter closely before reinstalling it. Look through the mesh toward a light source to ensure you can see light passing through the openings. If areas appear blocked, continue rinsing and brushing until the mesh is clear. The filter mesh should feel smooth to the touch with no rough spots or tears. If you notice damage to the filter itself, the filter should be replaced rather than reinstalled, as a damaged filter will not catch debris effectively.

Practical Takeaway: Rinse thoroughly, brush gently, consider a vinegar soak for stubborn deposits, and inspect for damage before reinstalling.

Checking and Cleaning the Filter Housing

While your drain filter is removed, examine the filter housing—the chamber where the filter sits inside your washer. Using your flashlight, look into the opening to see if any debris, lint, or standing water remains. Even after draining, small amounts of water may sit in the housing, which is normal. However, any visible lint or debris should be removed to ensure proper drainage and prevent clogs.

Free Guide to Finding Tire Store Locations Near You →

To clean the housing, use a damp cloth to wipe around the interior walls where the filter seals. Pay attention to the rubber gasket area, which creates a watertight seal when the filter is installed. Lint often accumulates around this gasket. Gently wipe away any debris you find. You can also use a small soft brush to reach into corners of the housing. Do not insert anything that could damage the internal components or get stuck inside.

Check the drain pump area visible through the filter opening. The drain pump is a small rotating mechanism that moves water out of the washer. Look for any obvious blockages or debris near the pump opening. If you see something blocking the pump, attempt to remove it carefully using needle-nose pliers or tweezers. Do not force anything or insert tools deeply into the machine. If you feel uncertain about what you