Lippert Components manufactures leveling systems found in many travel trailers, fifth wheels, and motorhomes built after the early 2000s. Their auto level technology uses hydraulic jacks paired with electronic sensors to detect and adjust the vehicle's pitch and roll automatically. When functioning properly, these systems detect uneven ground and deploy jacks to stabilize your RV within seconds.
Learn About Paying Your FGUA Bill Online →
The system works through a combination of tilt sensors mounted inside the RV and hydraulic actuators positioned at various points under the chassis. When you engage the auto level feature, onboard computers read sensor data and determine which jacks need to extend or retract. The entire process typically completes in under a minute, assuming no obstructions or mechanical issues exist.
Unlike manual leveling systems that require you to crank jacks by hand or operate individual controls, Lippert's auto systems prioritize convenience. However, this added complexity means more components can malfunction or become confused about your RV's actual orientation. Sensor drift, electrical glitches, or software hiccups occasionally cause the system to behave erratically—extending jacks when they should retract, or refusing to level at all.
Understanding what a reset actually accomplishes helps you know when to pursue one. A reset clears the system's memory and sensor calibration, forcing it to relearn your RV's baseline level position from scratch. This often resolves situations where the system "thinks" your rig is tilted when it's actually level, or vice versa. Resets don't repair broken hydraulic lines or replace failed sensors, but they address the most common software-related issues.
Practical takeaway: Before attempting a reset, confirm your Lippert system is actually malfunctioning rather than simply responding to truly uneven ground. Place your RV on a confirmed level surface using a bubble level, then observe whether the system still behaves incorrectly.
Resetting your Lippert auto level system should be your second or third troubleshooting step, not your first. Many apparent system failures actually stem from operator error, poor ground conditions, or temporary electrical hiccups that resolve themselves. Jumping straight to a reset wastes time and may complicate diagnosis if deeper problems exist.
Free Guide to Pay by Plate Illinois Billing →
Start by checking your RV's battery voltage. Lippert leveling systems require adequate power to function correctly—typically around 12 volts for standard systems. A battery voltage below 11 volts causes sensors to malfunction and prevents jacks from responding normally. If you've been boondocking without solar panels or running your generator frequently, low voltage may be your culprit. Simply recharging your house batteries often resolves leveling issues without any reset.
Next, visually inspect all hydraulic hoses connected to your leveling jacks. Look for visible leaks, cracked hoses, or disconnected fittings. Even small hydraulic leaks prevent jacks from holding pressure or extending fully. If you notice fluid pooling under your RV near the jack locations, you have a leak requiring professional repair rather than a system reset. A reset won't fix hydraulic failure.
Check that your RV is actually positioned on level ground. Many owners believe their campsite is level when it genuinely slopes 3-4 degrees in one direction. Use a quality bubble level placed on your RV's floor in multiple locations to verify. Sometimes what appears to be a leveling system malfunction is simply the system correctly identifying that your site is uneven and the hydraulic jacks have reached their maximum extension limits.
Review recent changes or damage. If you hit a pothole, scraped the undercarriage on an obstacle, or recently had work done to your RV's systems, physical damage to sensors or hydraulic lines may have occurred. These situations require professional inspection rather than a reset.
Practical takeaway: Document what happens before attempting a reset—which jacks deploy, whether error codes appear, and exactly when the malfunction started. This information helps you and a technician determine if reset will solve the problem or if professional service is necessary.
Lippert auto level systems include a wall-mounted control panel, typically located inside your RV near the main electrical panel or in a bedroom. Some manufacturers place these panels in wardrobes, under kitchen cabinetry, or along living area walls depending on floor plan. Spend a few minutes locating yours before attempting a reset—you'll need physical access to complete the procedure.
Free Guide to Mold Removal Methods for Walls →
The control panel usually measures approximately 6 by 8 inches and displays buttons labeled with terms like "Level," "Raise," "Lower," or "Retract." Modern Lippert panels often include small LED lights that illuminate different colors when the system operates or encounters errors. Older systems may feature simple mechanical buttons without any display screen. Your specific panel design depends on your RV's model year and manufacturer.
Open your RV's exterior storage compartments and check the sidewalls for a label or placard identifying your leveling system brand and model. You may find this information on a sticker listing system specifications, voltage requirements, and component identification. Take a photo of this label—it provides the exact model number you'll reference when seeking technical information or replacement parts.
Locate your RV's owner manuals, focusing on sections covering leveling systems or chassis systems. Lippert often publishes system-specific documentation included in the manuals that accompanied your RV. If you no longer have physical copies, contact your RV manufacturer's customer service department and request documentation for your chassis year and model. Many manufacturers now provide digital manual copies via email or their website. The manual contains reset procedures specific to your system version.
If you cannot locate original documentation, visit Lippert Components' website and use their product support section. You may search by model number or general description to find technical resources, instructional videos, and troubleshooting guides. Lippert occasionally publishes reset instructions tailored to different system versions released across various model years.
Practical takeaway: Gather your RV's model year, chassis type (trailer versus motorhome), and any Lippert system model numbers before beginning a reset. This information ensures you follow instructions designed for your specific system rather than attempting procedures meant for different versions.
Reset procedures vary significantly between Lippert system generations and variations. The process for a 2010 system differs from a 2018 system, and motorhome systems occasionally use different procedures than trailer systems. This section covers reset approaches for the most widely installed Lippert auto level configurations. Your specific system may require slight variations.
How to Delete Your Fitbit Account Guide →
Standard Lippert Auto Level Reset (Most Common): Turn off your RV's main battery disconnect switch, wait 30 seconds, then turn it back on. This soft reset clears the system's temporary memory without erasing calibration data. Many leveling glitches resolve with this simple power cycle. Allow the system two to three minutes after power-up for internal systems to reinitialize before operating the level controls.
If a soft reset doesn't resolve your issue, proceed to a full reset. Locate your leveling control panel and look for a small button labeled "Reset," "Calibrate," or sometimes marked with a wrench symbol. This button is often recessed, requiring you to press it using a straightened paperclip or similar thin object. Press and hold this button for 10-15 seconds while the system is powered on. The panel may display a blinking light or briefly shut off during this process—this is normal operation.
After releasing the reset button, your system enters a recalibration phase. Position your RV on a confirmed level surface using a bubble level. Do not move or rock the RV during this phase. Press the "Level" or "Auto" button on your control panel once. The system will deploy all jacks slightly and retract them fully, reading your new baseline level position. This calibration cycle typically takes 60-90 seconds. Once complete, you'll hear a final click or see a status light change, indicating calibration finished successfully.
Lippert Ground Leveling Systems: Older Lippert systems designed primarily for ground leveling rather than automatic operation sometimes use different reset approaches. These systems may include a manual override switch alongside automatic controls. To reset, switch the system to "Manual" mode, lower all jacks completely until they contact the ground firmly, then switch back to "Automatic" mode
This guide is for general information only and is not medical, financial, legal, or other professional advice. For decisions specific to your situation, consult a qualified professional. See our Editorial Policy.