How to Replace a CV Joint Boot Yourself

Understanding CV Joint Boots and Why They Fail

A CV joint boot is a rubber or plastic covering that protects the constant velocity joint on your vehicle's front axle. This joint allows your wheels to receive power from the engine while turning and moving up and down with suspension movement. The boot acts as a seal, keeping grease inside the joint and preventing dirt, water, and salt from entering. When the boot tears or cracks, moisture and contaminants can damage the joint itself, which is far more expensive to replace than a boot alone.

Free Guide to Growing Groundnuts at Home →

CV joint boots typically last between 80,000 and 160,000 miles, though this varies based on driving conditions and vehicle type. They fail for several reasons: repeated flexing as you turn corners, exposure to road debris and salt, UV damage from sunlight, and simple age. Cold weather accelerates deterioration because rubber becomes brittle in low temperatures. Rough roads with potholes and deep ditches put extra stress on the suspension and CV joints.

You'll recognize a failing boot by looking at your axle directly or noticing symptoms while driving. A torn boot may leak grease onto your wheel, creating a dark, oily residue. You might hear clicking sounds when turning at sharp angles—this indicates the joint inside has already suffered damage. Some people notice vibration during acceleration or a thumping sensation. The longer a damaged boot goes unfixed, the more damage spreads to the actual joint.

Replacing a boot yourself costs between $150 and $400 in parts, depending on your vehicle. A mechanic typically charges $300 to $800 per side, including labor. This makes DIY replacement a worthwhile project if you have basic mechanical skills and proper tools. The job takes 2 to 4 hours per side once you understand the process.

Practical Takeaway: Inspect your CV boots every 6 months by looking at your front axles and checking for grease splatter on your wheel. Catching a small tear early prevents expensive joint replacement down the road.

Gathering the Right Tools and Materials

Before you begin, collect all necessary tools and materials in one location. A complete toolkit prevents frustrating trips back to the store mid-repair. You'll need basic hand tools that most vehicle owners already have: a socket set (including 17mm, 19mm, 21mm, and 24mm sockets for most vehicles), wrenches, screwdrivers, and pliers. You'll also need jack stands rated for your vehicle's weight and a hydraulic floor jack to safely lift the car.

Free Guide to Understanding Toilet Leak Problems →

Specialized tools make the job significantly easier, though some are optional. A bearing puller (typically $30 to $50) helps remove the axle from the wheel hub without damaging it. A CV joint boot kit (usually $40 to $120) includes the new boot, bands or clamps, and grease. Buy a kit specific to your vehicle's make and model—CV joint designs vary significantly. A small rubber mallet helps tap components into place. A wire brush cleans away old grease and corrosion. A torque wrench (if you don't own one) ensures proper tightness for critical fasteners.

For safety equipment, wear nitrile gloves to protect your hands from grease and old CV joint lubricant, which can be difficult to clean off. Safety glasses protect your eyes when working beneath the vehicle or using compressed air. A creeper or cardboard allows you to work comfortably under the car. Have rags and newspaper available to catch spilled grease and contain mess.

Parts you'll need include the CV joint boot kit mentioned above, new axle shaft (if the current one is bent or severely damaged—usually $80 to $250), gasket sealer or silicone sealant, and potentially new CV joint clamps if the old ones are damaged. Check your vehicle's repair manual to confirm exact specifications. Many auto parts stores offer free advice on kit selection when you provide your vehicle information.

Practical Takeaway: Write down your vehicle's year, make, model, and engine size before visiting an auto parts store or ordering online. This ensures you get the correct boot kit and prevents costly mistakes.

Preparing Your Vehicle and Removing the Wheel

Safety is paramount when working on any vehicle. Park on a flat, level surface with plenty of space around all sides. Engage the parking brake firmly and place wheel chocks behind the rear wheels if you have them. If you must work near traffic, wear a bright safety vest and position a warning triangle or flares at least 100 feet behind your vehicle.

Free Step-by-Step Guide to Drawing Cabins →

Loosen the lug nuts on the wheel with the damaged CV boot while the vehicle is still on the ground. This requires less effort than trying to loosen them with the wheel suspended in air. Use the correct lug nut socket—usually 17mm or 19mm—and turn counterclockwise. You don't need to remove the nuts completely, just break them loose enough that you can finish the job once the wheel is lifted.

Position your floor jack under the vehicle's frame or designated jack point. Consult your owner's manual to locate the correct jacking point on your specific model—using the wrong spot can crack your car's frame. Lift the vehicle slowly and smoothly until the wheel clears the ground by about six inches. Immediately position jack stands under the frame on both sides as backup support. Lower the vehicle slowly onto the jack stands, leaving the floor jack in place as an extra safety measure.

Now remove the lug nuts completely and set them in a container where they won't roll away. Pull the wheel straight toward you to remove it from the hub. Some wheels stick due to rust between the wheel and hub surface. If this happens, tap around the wheel's inner edge with a rubber mallet rather than pulling forcefully, which can damage the wheel or hub. Place the wheel flat on the ground near your work area so you can see the exposed brake components and CV axle clearly.

Practical Takeaway: Invest in quality jack stands rated for at least 1.5 times your vehicle's weight. Never rely solely on a floor jack—jack stand failure has caused serious injuries and deaths.

Removing the Axle and Accessing the CV Boot

With the wheel removed, you can now access the CV axle assembly. The axle connects the transmission or differential to the wheel hub, and you need to separate these connections carefully. Start by removing the brake caliper if it blocks your access to the axle nut. Most vehicles use two bolts securing the caliper. Unbolt it and hang the caliper with wire from the suspension to prevent it from hanging by the brake hose, which damages the hose over time.

Get Your Free Belly Button Cleaning Guide →

Locate the CV axle nut, which is a large nut on the center of the wheel hub. This nut holds the axle in place with significant force—typically torqued to 150 to 250 foot-pounds depending on vehicle type. You may need to remove a center cap or cotter pin first. Some vehicles have a locking mechanism that prevents the nut from rotating. Have an assistant hold the brake pedal down firmly while you loosen the nut with a breaker bar and large socket. If you can't loosen it by hand, use a piece of pipe slipped over the breaker bar for additional leverage.

Next, disconnect the ball joints or steering linkage if they interfere with axle removal. This typically involves removing a cotter pin and castle nut, then using a ball joint separator tool (a wedge-shaped tool that forces the joint apart). Pull the steering knuckle and hub assembly outward to separate it from the inner CV joint at the transmission or differential. Be careful not to let the axle hang by the outer joint, as this puts excessive stress on it.

With the outer portion pulled clear, remove the inner axle connection at the transmission. This varies by vehicle type. Front-wheel-drive cars with transverse engines typically have a flange or socket-type joint that unbolts from the transmission. Rear-wheel-drive cars with independent rear suspension use different designs. Consult your specific repair manual for exact procedures. Once disconnected, carefully pull the entire axle assembly away from the vehicle and place it on a clean work surface.

Practical Takeaway: Take photographs with your phone before disassembling anything. Clear photos from multiple angles help you remember how components connect when reassembling.

Disassembling the CV Joint and Installing the New Boot

Once the axle is

Free Guide to Converting Feet Into Yards →