A submersible well pump sits at the bottom of your well, submerged in water, and pushes water up to your home or property. Unlike jet pumps that sit above ground, submersible pumps work by displacement—they're designed to function while completely underwater. This design means they're efficient and can pull water from deep wells, sometimes 300 feet or more below the surface.
Learn About Paying Your FGUA Bill Online →
The typical submersible pump assembly includes the pump itself (the motor and impeller unit), a drop pipe that carries water up, electrical wiring that runs alongside the pipe, and a foot valve at the bottom. The pump connects to a pressure tank, check valve, and pressure switch at the surface. When you need to pull the pump for repair, maintenance, or replacement, you're removing this entire assembly from the well—a process that requires planning and care.
Most residential submersible pumps last 8 to 15 years depending on water quality and usage. Signs that yours may need pulling include reduced water pressure, no water output, the pump running constantly, or obvious electrical issues like circuit breaker trips. Sand in your water is another indicator—it suggests the pump is drawing from the well bottom and may be failing.
Before attempting a pull, understand your pump's specifications. Check the manufacturer's documentation or your well installation records for the pump's horsepower, depth rating, and total depth of your well. A 1-horsepower pump pulling from 100 feet weighs differently than a 2-horsepower pump at 300 feet, and that matters for the equipment you'll need.
Practical Takeaway: Document your pump's make, model, horsepower, and installation depth before you start. Take a photo of the well cap and electrical connections. This information prevents mistakes during the pull and helps you order replacement parts if needed.
Pulling a submersible pump is not a guessing game about equipment. You need specific tools designed for this task, and cutting corners creates safety risks or damages your well infrastructure. The primary tool is a well pump puller or extraction rig. This isn't something you improvise with a hand winch and hope for the best.
Free Guide to Pay by Plate Illinois Billing →
A basic well pump puller is a mechanical device that clamps around the drop pipe at the top of the well. It uses leverage and mechanical advantage to pull the pipe and pump assembly upward. You can rent these from well equipment suppliers or specialized tool rental shops for roughly $40 to $100 per day. The rental price depends on your region and the depth of your well. A deeper well requiring heavier-duty equipment costs more.
Beyond the puller, gather these materials: a pipe wrench or two (14-inch minimum), adjustable wrenches, a screwdriver set, electrical wire connectors and tape, a flashlight, work gloves, safety glasses, and a bucket for small parts. You'll need something to hold the electrical wire and drop pipe as they emerge—many people use rope, nylon straps, or chain threaded through ceiling joists or a temporary frame to support the weight as you pull. Do not hold the wire or pipe by hand as it comes out; the weight and length create injury risk.
For safety, have a helper present. Pulling a pump solo increases the risk of the assembly dropping, the winch slipping, or you losing control of heavy materials. Your helper monitors the mechanical puller, watches for kinks in the pipe, and keeps the work area clear. They can also hold a flashlight and note any visible damage to components as they emerge from the well.
Consider renting or borrowing a submersible pump puller rather than purchasing one unless you pull pumps regularly. These tools are specialized, take up storage space, and you may use one once every decade. Rental is cost-effective and ensures you have equipment rated for your specific well depth.
Practical Takeaway: Call three equipment rental shops and three well service companies in your area to understand local rental costs and availability. Reserve your puller 2 to 3 days before you plan to work, as peak season (summer) can create shortages.
Before you touch anything, isolate the well from electrical power. This is not optional. Submersible pumps run on 240-volt or 120-volt circuits, and working on the pump or wire while power is active creates electrocution risk. Walk to your home's main electrical panel and switch off the breaker labeled for the well pump. If the breaker isn't clearly labeled, look for a double-pole breaker (which handles 240-volt circuits) and verify it's the well pump by testing the pressure switch or pump start button—nothing should happen when you press it.
Free Guide to Mold Removal Methods for Walls →
Some installations have a disconnect switch mounted on the well cap or on the exterior wall near the well. If yours does, switch this off first. Then trip the main breaker for the pump circuit. Test your work: try turning on a faucet. If water still flows from pressure in the tank, you've successfully cut power to the pump. If you get confused about which breaker controls the pump, call a licensed electrician to identify it. The cost is far less than an electrical injury.
Next, depressurize the system. Open a faucet in your home and let it run for 30 seconds to a minute. This drains pressure from the system lines. Walk back to the well and locate the check valve (typically located just above where the drop pipe enters the well cap). You may see a small drain plug on the check valve. If present, open this plug slightly to release any remaining pressure—water may spray out, so wear safety glasses and position a bucket underneath.
Now disconnect the electrical wire. At the well cap, you'll see the pump electrical wire (usually a three-conductor or four-conductor submersible pump cable) connected to the pressure switch or a junction box. Using a screwdriver, loosen the terminal screws and carefully pull the wire connectors apart. Label the wire connections with tape—mark which wire connected to which terminal. Use a marker to write "L1," "L2," "G" (ground), or however your system is labeled. This prevents confusion when reconnecting later or when a technician reassembles the pump.
If the wire goes to a pressure switch, disconnect it there. If it goes to a control box, disconnect at that box. Coil the electrical wire loosely and set it aside where it won't get tangled or damaged as you pull the pump.
Practical Takeaway: Take a close-up photo of the electrical connections before you disconnect them. Use masking tape to label each wire at the connection point with a permanent marker. Photograph the labels so you have a backup reference.
This is where the work becomes labor-intensive. Position your well pump puller over the well opening according to the tool's instructions. Most pullers clamp onto the drop pipe just below the well cap. Tighten the clamp firmly—loose clamps slip under load and drop everything. Your helper should verify the clamp is secure by attempting to wiggle the pipe; it shouldn't move.
How to Delete Your Fitbit Account Guide →
Begin pulling using smooth, steady pressure on the puller's handle or winch. Do not jerk or yank. Jerky movements cause the pipe to kink, damage the electrical wire, or cause the clamp to slip. Expect to pull for 5 to 15 minutes depending on how deep your pump sits. A 100-foot pull takes roughly 10 minutes at a steady pace. A 300-foot pull can take 30 to 45 minutes.
As the pipe emerges, support it from below with rope, straps, or chain to prevent the weight from pulling downward and kinking the drop pipe. Thread rope through the drop pipe every 20 feet as it emerges, then tie that rope to a ceiling joist, beam, or temporary frame in your well house. This distributes the weight and prevents the unsupported lower section from pulling the upper sections into a damaging bend.
Watch for resistance. If pulling suddenly becomes much harder, stop. Do not force it. Resistance indicates the pipe is kinked, the wire is tangled, or the foot valve is stuck. Forcing a stuck foot valve can damage both the valve and the pipe. If stuck, let the puller rest for 10 minutes and try again with steady pressure. Sometimes moisture in stuck valves loosens with rest.
This guide is for general information only and is not medical, financial, legal, or other professional advice. For decisions specific to your situation, consult a qualified professional. See our Editorial Policy.