Before you pick up a drill or screwdriver, you need to understand that license plate mounting rules vary significantly from state to state. This isn't just about preference—it's about legal compliance. Some states require plates on both the front and rear of your vehicle, while others only mandate a rear plate. A few states have specific rules about how plates must be positioned, the angle at which they're mounted, and even the materials you can use to secure them.
Learn About Paying Your FGUA Bill Online →
For example, California requires both front and rear plates, and they must be clearly visible and not obscured. New York similarly requires both plates. However, states like Alabama, Mississippi, and South Carolina only require a rear plate. If you're driving across state lines, you'll want to know the most restrictive requirements you might encounter. Many drivers moving from one state to another discover their mounting setup needs adjustment.
The angle of your plate matters too. Most states require plates to be mounted so they're perpendicular to the ground and clearly readable from a distance of 75 to 100 feet. Some states have explicit rules about the angle—typically specifying that plates cannot be tilted more than 15 degrees from vertical. If your plate is angled too severely backward or forward, you risk getting stopped by law enforcement, and in some jurisdictions, you could receive a citation.
Some vehicles present unique mounting challenges. Trucks with aftermarket bumpers, vehicles with curved front ends, and cars with limited bumper space all require different approaches. Understanding your state's rules before you start prevents costly mistakes, like drilling holes in the wrong spots or purchasing mounting hardware that won't work with your vehicle's design.
Takeaway: Check your state's DMV website or contact your local motor vehicle office to confirm whether you need one or two plates, the required angle, and any specific visibility standards before beginning installation.
Mounting a license plate doesn't require expensive equipment, but using the right tools makes the job safer and produces better results. Your basic toolkit should include a drill with appropriate bits, a Phillips head screwdriver, a power drill or hand drill, measuring tape, a level, and a marker or pencil for marking hole positions. For most vehicles, a standard 1/4-inch drill bit works for license plate mounting hardware.
Free Guide to Pay by Plate Illinois Billing →
The mounting hardware itself comes in several varieties. The most common option is a stainless steel bolt kit specifically designed for license plates. These kits typically include bolts (usually 1/4 inch in diameter and 3/4 inch long), washers, and nuts. Stainless steel is preferable because it resists rust and corrosion, which is especially important in regions with road salt or high humidity. You can purchase these kits at auto parts stores for $8 to $15, and they're also available online. Some kits include rubber spacers, which help protect your vehicle's bumper and allow for slight angle adjustments.
For the actual plate, you'll have received it from your state's DMV when you registered your vehicle. The plate itself comes with two pre-drilled holes (or sometimes four, depending on the design) positioned at standard intervals. These holes align with mounting brackets on your vehicle in most cases, though aftermarket vehicles or older cars may have different bracket positions.
Consider whether you want a protective cover or frame around your plate. License plate frames come in plastic or stainless steel and can protect the edges of the plate from damage. However, check your state's rules—some states prohibit frames that obscure any part of the plate number or registration information. A clear plastic frame is usually the safest option if frames are legal in your state.
Takeaway: Invest in a stainless steel bolt kit with washers and nuts designed specifically for license plates; this $10–15 purchase prevents rust problems and ensures secure mounting for years.
The preparation phase determines whether your final result looks professional or haphazard. Start by cleaning the area where you'll mount the plate. Use a damp cloth or car wash to remove dirt, grime, and debris from the bumper or mounting area. A clean surface helps you see the existing holes or brackets clearly and ensures accurate measurements. Dry the area completely before proceeding.
Free Guide to Mold Removal Methods for Walls →
Next, locate your vehicle's mounting brackets. On most modern vehicles, the front and rear bumpers have pre-installed metal brackets with mounting holes. These brackets are specifically designed to accept license plate bolts. Look closely at your bumper—you'll see small rectangular openings or slight depressions where brackets sit. Some vehicles have the brackets recessed into the bumper itself, while others have them protruding slightly.
Place your license plate against the bumper and align it with these existing holes. This is where a measuring tape and level become valuable. You want the plate centered on the bumper and level—not tilted left to right. Use a level to verify the plate sits perpendicular to the ground. Mark the hole positions with a marker or pencil by looking through the pre-drilled holes in the plate and making small marks on the bumper. If your vehicle doesn't have pre-installed brackets, you'll need to determine hole positions yourself, measuring from the bumper's edges to ensure the plate is centered.
For vehicles without existing brackets, position your plate so it's roughly centered, about 12 inches from the bumper's bottom edge. This positioning looks proportional and keeps the plate away from road debris. Take your time with this step—poor initial positioning is the most common reason people need to remount plates.
Takeaway: Use a level to ensure your plate sits straight before marking hole positions; taking an extra 10 minutes here prevents visible misalignment that's difficult to correct after drilling.
Once you've marked the hole locations, you're ready to drill. This is the point of no return, so double-check your marks one final time. For metal bumpers, use a 1/4-inch drill bit with your power drill. Start at low speed to create a pilot hole—this prevents the bit from slipping and damaging the bumper's paint. Once the pilot hole is established, increase your speed and drill completely through the bumper. You'll feel a slight pop or release when the bit breaks through the back side of the bumper.
How to Delete Your Fitbit Account Guide →
For plastic bumpers, which are common on newer vehicles, use the same 1/4-inch bit but maintain lower speed throughout. Plastic can crack or melt if drilled too quickly. Some technicians recommend using a backing plate—a piece of scrap wood held against the back of the bumper—to support the plastic as you drill. This prevents the bit from catching and tearing the bumper material.
After drilling, inspect both sides of the bumper. Remove any plastic or metal shavings with a wire brush or cloth. This cleanup is important because debris can trap moisture and cause rust around the mounting holes. If you see any paint damage, consider touching it up with touch-up paint from your vehicle's manufacturer to prevent rust.
Now insert your mounting bolts. Place a washer on the bolt, insert it through the license plate hole, then through the bumper hole you just drilled. On the back side of the bumper, add another washer and thread on the nut. Tighten by hand first, then use a wrench to secure the nut firmly. The bolt should be snug enough that the plate doesn't move, but not so tight that you crack the bumper (especially important for plastic bumpers). A good rule: tighten until you feel resistance, then give it a quarter turn more.
Takeaway: Drill slowly on plastic bumpers and use a backing plate to prevent cracking; take time to remove all debris before installing bolts to protect against rust.
Most vehicles requiring two license plates need the same mounting process repeated on both the front and rear bumpers. The rear mounting is usually straightforward, following the same process you used for the front. However, front mounting can present challenges—some vehicles have limited space, curved bumpers, or integrated design elements that complicate positioning.
Learn How to Grow Sweet Corn at Home →
One common problem is plate wobbling after installation. This typically happens when bolts are under-tightened or when washers are too small, allowing the plate to move slightly over bumps. To fix wobbling, tighten the bolts slightly more, or consider adding a rubber spacer kit, which
This guide is for general information only and is not medical, financial, legal, or other professional advice. For decisions specific to your situation, consult a qualified professional. See our Editorial Policy.