A dripping kitchen faucet isn't just annoying—it's also expensive. The EPA estimates that a single faucet dripping at one drop per second wastes over 3,000 gallons of water annually. That's equivalent to taking 180 showers. Most people notice the sound before they notice the water bill, which is why understanding what causes these drips matters before you decide whether to tackle the repair yourself.
Learn About Paying Your FGUA Bill Online →
Inside your faucet, water flow is controlled by internal seals and valves. The most common culprit behind drips is a worn-out washer or cartridge. Washers are rubber or rubber-like discs that sit inside the faucet valve, creating a watertight seal when you turn the handle off. Over time—typically between three to five years of normal use—these washers become compressed, cracked, or corroded. When the washer no longer fits snugly, water seeps through and drips from the spout or base.
Different faucet types fail in different ways. Compression faucets (the kind with two separate handles) rely entirely on washers to stop water flow. Single-handle faucets use cartridges or ball mechanisms instead. Cartridges are cylindrical pieces with multiple chambers that direct water flow and temperature. When cartridges wear down, they allow water to bypass their seals. Ball faucets—common in kitchens—contain a domed cap with inlet and outlet holes. Sand, mineral buildup, or debris can lodge in these holes and prevent a complete seal.
Practical takeaway: Before buying parts, identify your faucet type. Look under the sink at the handles. Two separate handles indicate a compression faucet. One handle that moves side-to-side suggests a ball faucet. One handle that moves forward and back, or a single spout with a cartridge visible, indicates a cartridge faucet. Knowing this type saves you from purchasing the wrong repair kit.
You don't need an expensive toolkit to fix a dripping faucet. Most repairs use basic tools found in an average home or available for under $20. However, having the correct items matters—using the wrong wrench size or screwdriver type wastes time and risks stripping bolts or screws.
Free Guide to Pay by Plate Illinois Billing →
For nearly all faucet repairs, you'll need an adjustable wrench (one tool that fits multiple bolt sizes), a Phillips screwdriver, a flathead screwdriver, and an Allen wrench set. An adjustable wrench costs $8–15 and handles the different bolt sizes you'll encounter under the sink. You'll also need a towel or small bucket—water will spill when you disconnect parts, and kitchen floors aren't the place for puddles. An old toothbrush proves surprisingly useful for scrubbing mineral deposits off cartridges.
Replacement parts depend on your faucet type. For compression faucets, purchase a washer assortment kit ($5–8), which includes various washer sizes. You'll also need new O-rings (rubber rings that create seals around the valve stem) for about $3–5. For cartridge faucets, you need to replace the entire cartridge, which costs $15–50 depending on the brand and model. Ball faucets typically require a repair kit ($20–40) that includes the internal components. Your faucet's manufacturer and model number determine which exact cartridge or kit you need.
Finding your faucet model is straightforward. Look at the faucet itself—Moen, Kohler, Delta, Pfister, and Grohe are common brands. The model number is usually stamped on the faucet body or the supply lines underneath. Some faucets have a sticker behind the faucet base. Write down the brand and model before shopping. This single step prevents buying incorrect parts and making multiple trips to the hardware store.
Practical takeaway: Create a small kit and leave it under your sink: adjustable wrench, Phillips and flathead screwdrivers, Allen wrenches, and the replacement cartridge or washer kit specific to your faucet. When a drip starts, you won't scramble to find tools. Most repairs take 20–45 minutes once you have everything gathered.
Before touching any part of your faucet, you must shut off water supply. This single step prevents flooding and makes the repair safe and manageable. Water will still be in the lines after shutting off the supply, but it won't continue flowing while you work.
Free Guide to Mold Removal Methods for Walls →
Under your sink, you'll find two small valves (one for hot water, one for cold) with knobs or handles. Turn both clockwise until they stop. Don't force them—they should turn smoothly. Once closed, turn on your faucet to confirm water has stopped. A little water may come out (it's trapped in the lines), but it should stop flowing within a few seconds. If no valves exist under your sink, you may need to locate your home's main water shut-off valve, usually found in a basement or utility room. If you can't find it, call a plumber for a consultation—they can show you where it is and ensure it works.
After shutting off water, dry the faucet and surrounding area thoroughly. A wet workspace leads to slips and makes it difficult to see what you're doing. Lay a towel on the counter and floor to catch any remaining water drips. Place your tools within arm's reach so you're not fumbling or reaching across the sink. If your faucet has decorative trim or caps, keep them in a small container so they don't roll away.
This preparation phase is where patience pays off. Rushing increases the chance you'll strip a bolt, lose a small screw, or miss seeing how components fit together. Take photos or videos with your phone as you disassemble parts. These images serve as a visual guide when reassembling—especially useful if you take a break and return to the repair later.
Practical takeaway: Spend five minutes on setup before touching a wrench. Shut off water, dry the area, lay out tools, and photograph the faucet from different angles. This preparation reduces frustration and makes the actual repair faster and more successful.
Compression faucets have two handles and are the most straightforward to repair. The drip typically comes from a worn washer inside the valve seat. This repair involves removing the handle, unscrewing the packing nut (a hexagonal piece that holds the stem in place), pulling out the stem, and replacing the washer at the bottom.
How to Delete Your Fitbit Account Guide →
Start by locating the handle's fastening screw. It's usually hidden under a decorative cap or plug at the base of the handle. Pop off this cap with a flathead screwdriver, then remove the screw underneath. The handle comes right off. Next, use your adjustable wrench to turn the packing nut counterclockwise. This nut is directly below where the handle connects. Turn it until it's loose enough to remove by hand. You'll then see the valve stem—a cylindrical piece that can be pulled straight out.
At the bottom of the stem, you'll see the washer held in place by a brass screw. Using your flathead screwdriver, remove this screw. The old washer will likely be discolored, shriveled, or cracked—this is what caused the drip. Replace it with a new washer from your kit, ensuring it's the correct size. Reinstall the brass screw, but don't overtighten. A hand-tight fit is sufficient.
Before reassembling, turn off the water supply valve under the sink and open the faucet to release any remaining pressure. Look inside the valve seat (the opening where the stem goes) for debris or corrosion. If you see mineral buildup or debris, scrub it gently with an old toothbrush. Reinstall the stem, hand-tighten the packing nut, reattach the handle, and turn the water back on slowly. Test both hot and cold sides. If dripping continues, the valve seat may be damaged and require professional replacement.
Practical takeaway: Compression faucet repairs are ideal for first-
This guide is for general information only and is not medical, financial, legal, or other professional advice. For decisions specific to your situation, consult a qualified professional. See our Editorial Policy.