Hot tub water isn't just water—it's a carefully balanced chemical environment that keeps you safe and comfortable. Three main chemical measurements control whether your tub stays clean and healthy: pH, alkalinity, and sanitizer levels. Think of these like the three legs of a stool. If any one is off, the whole system wobbles.
Learn About Paying Your FGUA Bill Online →
pH measures how acidic or basic your water is on a scale from 0 to 14. For hot tubs, you want to stay between 7.2 and 7.8. When pH is too low, the water becomes acidic and can damage your tub's surfaces and equipment. When it's too high, the water becomes cloudy and sanitizers stop working effectively. The sweet spot—around 7.4—mimics human tears and keeps everything balanced.
Alkalinity acts as a pH buffer. It's the water's ability to resist sudden pH changes. You want alkalinity between 80 and 120 parts per million (ppm). Without proper alkalinity, your pH will swing wildly every time you add chemicals or even when the sun hits the water. Low alkalinity means your pH crashes. High alkalinity means you can't adjust pH without adding huge amounts of chemicals.
Sanitizer levels kill bacteria and viruses that cause infections and cloudy water. Most hot tubs use chlorine or bromine as sanitizers. Chlorine works better in cooler water and breaks down faster in hot water. Bromine works better at higher temperatures (which is why hot tubs use it) and lasts longer. You want bromine levels at 3-5 ppm in a hot tub. Without proper sanitizer levels, bacteria multiply quickly in the warm environment.
Practical takeaway: Buy an inexpensive test kit (they cost $20-40) that measures all three: pH, alkalinity, and sanitizer. Test strips are cheaper but less accurate than liquid kits. Knowing these three numbers is the foundation of every cleaning decision you'll make.
Testing is the most important step most people skip. You can't fix what you don't measure. The frequency of testing depends on how much you use your tub. A hot tub used daily by multiple people needs testing at least twice weekly. A tub used once a week by one person might only need testing weekly. If you're not sure where to start, test twice a week until you understand how your water behaves.
Free Guide to Pay by Plate Illinois Billing →
For test strips: dip the strip in water away from the jets, let it sit for 15-20 seconds as directed on the bottle, then compare the colored pads to the chart. The hardest part is matching colors accurately. Lighting matters—test strips under natural daylight, not fluorescent lights which distort colors.
For liquid test kits: you'll fill small vials with hot tub water, add reagent drops to each vial, and wait for color changes. These kits show you exactly how many drops it took to create color change, which directly tells you the ppm level. A basic liquid kit costs $25-35 and lasts through 50-100 tests. They're more work but significantly more accurate than strips.
When you get your results, don't panic if numbers are slightly off. Everything doesn't need to be perfect all at once. Adjust one chemical at a time. If pH is 7.2 and alkalinity is 75 ppm, fix alkalinity first (raise it by adding alkalinity increaser), then retest. When alkalinity climbs to the right range, retest pH—it often corrects itself. This prevents overchemicalization.
You'll notice patterns over time. Water that sits untouched for a week might slowly climb in pH. Water used every night by four people might need frequent sanitizer additions. Understanding your tub's specific patterns beats following generic schedules. One owner's twice-weekly schedule might be another person's weekly schedule.
Practical takeaway: Create a simple testing log (even a notes app on your phone works). Write the date, all three numbers, what chemicals you added, and any observations. After four weeks, you'll see clear patterns that show exactly how often your tub needs attention.
If your pH is too low (below 7.2), you need to raise it. This isn't a quick fix—aggressive pH adjustments cause cloudiness. Use a product called pH increaser (sodium carbonate). Most packages recommend adding a specific amount per gallon of water in your tub. A typical 400-gallon tub might need 1-2 pounds to raise pH by one point. Always follow your product's specific directions.
Free Guide to Mold Removal Methods for Walls →
The process: turn off all jets, dissolve the pH increaser in a bucket of water first (don't dump powder directly in), pour it around the tub away from the intake, let it dissolve, and wait at least two hours before retesting. Don't add more chemicals during this waiting period. Patience prevents over-adjustment.
If your pH is too high (above 7.8), you need to lower it using pH decreaser (sodium bisulfate). High pH is more common than low pH because chlorine and bromine sanitizers naturally raise pH as they dissolve. Again, follow package directions carefully. A 400-gallon tub might need 1-2 pounds to drop pH by one point. Dissolve it first, pour it away from intake, wait two hours, retest.
Here's where most people make mistakes: they make huge adjustments then are shocked when pH swings the other direction. If pH is 8.1 and you want 7.4, that's only 0.7 points off target. Add half of what the package recommends for a one-point drop. Wait. Retest. This takes longer but prevents the pH seesaw where you're constantly chasing perfect numbers.
One common issue: new users adjust pH multiple times in one day, then watch their pH spike 1.5 points overnight. This happens because adjustments take time to fully dissolve and distribute. The rule: adjust once, wait two hours minimum, retest, then decide if another adjustment is needed. Most people only need adjustments every three to seven days, not daily.
Practical takeaway: Write down your starting pH, the amount of increaser or decreaser you added, and what happened after two hours. After two or three adjustments, you'll understand how much your specific tub needs and can make smaller, more accurate adjustments.
Sanitizer is your tub's immune system. Without it, bacteria and algae take over. For bromine (the standard for hot tubs), you want 3-5 ppm. For chlorine, you want 2-4 ppm. Testing tells you if you're low and need to add more. You'll notice a pattern: sanitizer levels drop over time because they work (they actually get "used up" killing bacteria). This is normal.
How to Delete Your Fitbit Account Guide →
Bromine comes in tablets, sticks, or powder. Tablets go in a floating dispenser or in-line feeder. The advantage of tablets is slow, steady release. The disadvantage is less control—you can't quickly boost levels if they drop. Bromine powder (also called brominating agent) works immediately for quick fixes. Most owners use tablets for daily sanitizing and powder for occasional boosts.
Chlorine also comes in tablets, sticks, or powder, but hot tub chlorine is different from pool chlorine. Dichlor and trichlor are hot tub chlorines that release quickly. Regular calcium hypochlorite (pool chlorine) releases chlorine inconsistently at high temperatures. If using chlorine, specifically buy hot tub chlorine, not pool chlorine.
Adding sanitizer to an empty tub after draining is different from maintaining levels in used water. When you first fill your tub, you're starting from zero and might need higher doses initially. Once established, you're usually just replacing what got used. A heavily used tub might need sanitizer additions twice weekly. A lightly used tub might only need weekly additions.
One critical concept: chlorine and bromine create byproducts called chloramines or bromamines when they work. These cause that "chemical" smell people notice in pools and hot tubs. You can
This guide is for general information only and is not medical, financial, legal, or other professional advice. For decisions specific to your situation, consult a qualified professional. See our Editorial Policy.