Get Your Free Weed Wacker String Replacement Guide

Understanding Weed Wacker String Types and Materials

Weed wacker string, also called trimmer line or cutting head string, comes in several different materials and thicknesses. The most common type is nylon, which makes up about 95% of all residential weed wacker strings on the market. Nylon string works well because it's durable, affordable, and safe to use around garden edges and delicate plants. The string breaks down over time from UV exposure and friction against grass and weeds, which is why replacement becomes necessary after regular use.

Get Your Free California License Reinstatement Guide →

String thickness is measured in inches or millimeters, with common residential sizes ranging from 0.065 inches to 0.105 inches in diameter. Thicker string cuts through tougher weeds and brush more effectively, but it also uses more fuel and puts extra strain on your weed wacker's motor. Thinner string works fine for light yard maintenance but may break frequently if you're cutting dense or woody vegetation. Most homeowners use string between 0.080 and 0.095 inches thick for general lawn trimming.

Some specialty string options exist beyond standard nylon. Co-polymer blends offer increased durability and may last 15-20% longer than basic nylon. Twisted or spiral-shaped strings provide better cutting performance in certain conditions. However, these premium options cost two to three times more than standard nylon and aren't necessary for typical residential use.

Before purchasing replacement string, check your weed wacker's manual or the specification label on the machine itself. This tells you the correct diameter your trimmer head requires. Buying the wrong size won't fit properly and could damage your equipment. Your weed wacker model number appears on a sticker or plate attached to the machine, usually near the handle or motor housing.

Practical takeaway: Locate your weed wacker's model number and manual now, then note the recommended string diameter. This information prevents purchasing mistakes and ensures you have the right specifications when you're ready to replace the string.

Step-by-Step Instructions for String Removal

Removing old weed wacker string is the first part of the replacement process. Before starting, unplug your electric weed wacker or ensure the gas tank is empty on a gas-powered model. Safety is essential because the cutting head can still rotate even when the power is off if you accidentally trigger the switch. Let the equipment cool for at least 15 minutes after use, as the trimmer head and string become very hot during operation.

Get Your Free Lawn Clover Removal Guide →

Most residential weed wackers use one of two cutting head designs: the fixed-string head or the automatic bump-feed head. Fixed heads have string wound around a spool inside the head cover. To access this spool, you'll need to remove the circular head cover, which usually requires turning a large nut counterclockwise by hand or with a wrench. Once the cover comes off, you can see the spool clearly. The old string either unwinds from the spool or sits in grooves or channels on the spool's surface. Simply pull out all remaining string pieces and discard them.

Bump-feed heads work differently and are becoming more common on newer models. In these designs, string is stored on a retractable spool inside the head, and you get fresh line by tapping the head on the ground while the trimmer runs. To replace string in this type, you must remove the entire head assembly from the shaft. This typically requires removing one or two bolts that hold the head in place. Once the head comes off, look for a small cover or cap on top. Prying this cover off gently with a flat screwdriver reveals the spool inside. Pull out old string and any debris that may have accumulated.

Clean the cutting head while it's open. Use a small brush or compressed air to remove dirt, grass clippings, and debris. This prevents buildup that can interfere with string feeding and causes the motor to work harder. Check that the string channels or grooves aren't cracked or damaged. Minor wear is normal, but deep cracks mean you should replace the entire head.

Practical takeaway: Take a photo of your cutting head before disassembling it. This reference photo helps during reassembly, especially if you haven't done this task before. Mark any bolts or small parts in a container so nothing gets lost.

Measuring and Preparing Your Replacement String

Weed wacker string doesn't come pre-loaded into trimmer heads at retail shops. You purchase it on spools and wind it manually onto your equipment's spool. String spools are available at hardware stores, garden centers, and online retailers in various lengths. A standard spool contains 25 to 100 feet of string, while bulk spools may contain 500 feet or more. For occasional homeowners who trim their yards a few times yearly, a 25-foot spool may last an entire season. Those who maintain larger properties or trim weekly might go through 100 feet in a single season.

Get Your Free Great Clips Coupons Information Guide →

Before winding new string, measure the correct length for your specific trimmer head. This information appears in your equipment's manual under "string length" or "line length." Most residential fixed-head trimmers use between 15 and 25 feet of string per head, though some larger commercial models require more. Using too little string leaves you with short cutting swaths and forces more passes over your yard. Using too much string wastes material and can overload the motor, causing it to stall or shut off.

Cut your replacement string to the measured length using a utility knife or sharp scissors. A clean, straight cut makes winding much easier. Some people make the cut at a slight angle, which creates a pointed end that threads more smoothly into the spool's starting point or anchor hole. If you're replacing string on a bump-feed head, check your manual for the specific length, as these heads often require different amounts than fixed heads.

Inspect your string before winding it onto the spool. Look for flat spots, discoloration, or stiffness that might indicate the spool has been stored in extreme heat or direct sunlight. Old string that's been sitting in a warehouse for years may not perform as well as fresh stock. If the string feels brittle or breaks easily when you bend it, don't use it. Fresh string should bend smoothly without cracking or breaking.

Practical takeaway: Keep your equipment's manual in a waterproof folder near your garage or shed, along with a note showing the required string diameter and length. This saves time when you're ready to replace string and prevents purchasing errors.

Winding String Onto Your Trimmer Head

Winding string correctly onto your trimmer head is crucial for proper operation. Incorrect winding causes the string to tangle, jam, or fail to feed properly during use. Most fixed-head trimmers have two anchor points or notches on the spool where you insert the string's end. These notches prevent the string from unwinding while you wind new line. Find these anchor points on your spool and insert about 2 inches of your cut string into one of them, pushing until it seats firmly in the notch.

Learn About Loan Repayment Options and Strategies →

Wind the string tightly and evenly around the spool in the direction indicated by arrows on the spool itself. Always wind in the direction the arrows point—winding backward tangles the string. Keep tension on the string as you wind, making sure each wrap sits next to the previous one without overlapping or leaving gaps. This tight, organized winding ensures the string feeds smoothly when you use the trimmer. Loose or overlapping winds cause jams and tangles that make the trimmer unusable.

Continue winding until you've wrapped nearly all the string around the spool, leaving about 4 to 6 inches free. Thread this final length through the second anchor notch on the spool. This double-anchor design allows both ends of the string to feed out simultaneously, providing balanced cutting power. If your spool has only one anchor point, you may have a single-line head design, which is less common on residential equipment but still functional.

Once both ends are anchored, reinstall the spool inside the head cover and secure the cover tightly. Make sure no string protrudes beyond where the cover connects to the head, as protruding string will immediately wrap around the head or break off when you start the trimmer. The string should be hidden inside the head cover, with only the tips visible at the cutting edges. Check that the cover is seated evenly all the way around before tightening the retaining nut.