Get Your Free Water Heater Pilot Light Guide

Understanding Your Water Heater's Pilot Light System

A pilot light is a small, continuous flame inside your water heater that ignites the main burner when heat is needed. This component has been a standard feature in gas water heaters for decades, though newer models increasingly use electronic ignition systems instead. The pilot light typically burns at a temperature of around 1,300 degrees Fahrenheit and uses only a small amount of gas—roughly equivalent to a lit birthday candle in terms of fuel consumption.

Free Guide to Roku Streaming Options →

The pilot light serves as the ignition source for your water heater's main burner. When the thermostat detects that water temperature has dropped below the set level, it signals the gas valve to open. The pilot light then ignites the gas flowing to the main burner, heating the water in the tank. Once the water reaches the desired temperature, the thermostat shuts off the gas flow, and the main burner stops—though the pilot light continues burning to remain ready for the next heating cycle.

Most pilot lights have a thermocouple or thermopile attached to them. These safety devices detect the heat from the pilot flame and generate a small electrical signal that tells the gas valve it's safe to allow gas flow. If the pilot light goes out, the thermocouple cools down, the signal stops, and the gas valve automatically closes. This is a crucial safety feature that prevents dangerous gas accumulation in your home.

Water heaters with pilot lights are found in millions of homes across North America. According to the U.S. Energy Information Administration, approximately 40% of American households use gas as their primary water heating fuel. Many of these systems still rely on pilot light ignition, making understanding this component valuable for homeowners.

Practical takeaway: Recognizing how your pilot light system works helps you identify problems early and understand when professional service is truly needed versus when simple troubleshooting may resolve the issue.

Identifying When Your Pilot Light Has Gone Out

The most obvious sign that your pilot light has gone out is lack of hot water. When you turn on a hot water tap and receive only cold water, even after waiting several minutes, the pilot light may be the culprit. However, this symptom can indicate other problems too, so it's important to verify the actual status of your pilot light before assuming that's the issue.

Learn About Neurology Centers and Finding Care →

To check whether your pilot light is actually burning, you'll need to locate your water heater and access the combustion chamber. Most water heaters are located in basements, utility closets, or garages. Look for a small access panel or cover, typically located near the bottom of the tank. This panel usually has a small window or opening that allows you to see inside the combustion chamber. In a dark room or at night, you should be able to see a small blue flame if the pilot light is operating. The flame should be steady and roughly the size of a kitchen match flame.

If you cannot see a flame, the pilot light is out. Before attempting any troubleshooting, ensure the area is well-ventilated and that you smell no gas. If you detect a strong gas odor, leave the area, open windows, and contact your gas utility's emergency line immediately. Never use matches or lighters to investigate a potential gas leak.

Other indicators that something is wrong with your pilot light include a yellow or orange flame instead of blue (which can indicate incomplete combustion or debris in the burner), a flame that flickers or moves erratically, or a flame that doesn't stay lit even immediately after you light it. A healthy pilot light burns with a steady blue flame and should remain lit continuously.

Practical takeaway: Locate your water heater now and familiarize yourself with where the pilot light viewing window is. This preparation means you'll know exactly where to look if you need to troubleshoot hot water problems later.

Common Reasons Why Pilot Lights Go Out

Several factors can cause a pilot light to extinguish. Understanding these reasons helps determine whether the issue is something you might address yourself or requires professional attention. The most common cause is a faulty thermocouple—the safety device that detects the pilot flame's heat. Over time, thermocouples accumulate mineral deposits or rust, reducing their ability to generate the electrical signal needed to keep the gas valve open. When a thermocouple fails, the gas valve automatically closes to prevent gas from flowing without an ignition source, and the pilot light goes out.

Get Your Free Guide to System32 and Computer Safety →

A second frequent cause is a malfunctioning gas valve. The gas valve controls gas flow to both the pilot light and main burner. If the valve develops internal corrosion or mechanical problems, it may not deliver gas to the pilot light consistently. Signs of a failing gas valve include a pilot light that ignites but won't stay lit, or one that requires multiple attempts to light. Gas valves typically last 10 to 15 years before showing signs of wear.

Drafts and air currents can blow out pilot lights, particularly in homes with significant air movement from HVAC systems, open windows, or doors near the water heater. Some water heater models are more susceptible to draft-related pilot light outages than others. Homes with recently installed exhaust fans or HVAC modifications sometimes experience new pilot light problems for this reason.

A clogged pilot light orifice—the small opening where gas flows to create the pilot flame—can prevent the light from staying lit or lighting at all. Dust, mineral deposits, or rust particles can accumulate in this tiny opening over time. The combustion chamber air intake, which provides oxygen for the pilot light to burn, can also become blocked by debris, lint, or dust accumulation.

Water heater age matters significantly. The U.S. Department of Energy notes that most conventional storage tank water heaters last between 8 and 12 years. Older units experience more frequent pilot light issues as components wear out and internal corrosion develops. Sediment buildup inside the tank can also affect the heater's overall function and contribute to various problems, including pilot light issues.

Practical takeaway: If your pilot light goes out repeatedly, document how often this happens and what conditions seem to trigger it. This information helps any technician you contact understand the problem more quickly.

Steps for Relighting Your Pilot Light Safely

Before attempting to relight your pilot light, always read the instructions on your specific water heater model, as procedures vary. Most units have detailed relighting instructions printed on a label attached to the tank or inside the combustion chamber door. Locate and review these instructions before proceeding. If instructions are missing or illegible, contact the manufacturer or a professional technician rather than guessing at the procedure.

Get Your Free Terrarium Starter Guide →

The general process for relighting a pilot light involves several steps. First, turn off the gas supply using the control knob on your water heater. This knob is typically located on the thermostat or gas valve assembly. Turn it fully to the OFF position. Then wait several minutes—at least five—to allow any residual gas to dissipate from the combustion chamber. This waiting period is crucial for safety.

Next, locate the pilot light button or knob. On many models, you'll need to turn the thermostat control to the PILOT setting. Look for the pilot light port, which is typically a small opening or window in the combustion chamber area. Some models have an ignition button you'll need to press continuously while following additional steps. Other models may require you to hold a match or lighter to the pilot light opening.

If using a match or lighter, hold the flame near the pilot light opening while simultaneously turning the gas control knob to the PILOT position. You should see a small flame ignite. Once it does, continue holding the pilot button (if your model has one) for 30 to 60 seconds after the flame appears. This holding period allows the thermocouple to heat up enough to generate the electrical signal that keeps the gas valve open.

After releasing the button, watch the flame for several minutes to confirm it remains lit. If the light goes out immediately or within a few minutes, the thermocouple or gas valve likely needs professional service. Do not repeatedly attempt to light the pilot if it won't stay lit, as this can allow gas to accumulate dangerously in the combustion chamber.

Once the pilot light is successfully lit and burning steadily with a blue flame, turn the thermostat control to your desired temperature setting. The main burner should eventually ignite as the water cools slightly from its set temperature. Listen for the ignition sound and watch for the larger flame of the