Get Your Free Spare Tire Replacement Guide

Understanding Spare Tire Basics and Why You Need Replacement Information

A spare tire is one of the most important safety components on your vehicle, yet many drivers don't understand when or how to replace one. Whether you drive a sedan, truck, SUV, or van, knowing about spare tire replacement can help you handle roadside emergencies more confidently. According to tire industry data, approximately 1 in 4 drivers has never changed a tire, and many don't know what type of spare tire their vehicle has or where it's located.

Learn About Dental Implant Options in Shreveport →

Spare tires come in several varieties, and the type matters significantly for how you'll replace a flat. Full-size spares are identical to your regular tires and can be driven at normal speeds indefinitely. Temporary spares, also called donuts, are smaller and lighter, designed only for short-distance driving at reduced speeds. Run-flat tires allow continued driving even after a puncture, though they still need professional inspection. Some vehicles have tire repair kits instead of physical spares. Understanding which type your vehicle has is the first step toward being prepared.

Many vehicle owners discover their spare tire situation only when they experience a flat. By that time, stress and time pressure make learning difficult. A spare tire replacement guide provides you with information in advance, so you won't be scrambling during an actual roadside emergency. You'll learn where to find your spare, what tools you'll need, and the proper steps to follow. This preparation can save you time, reduce frustration, and help you stay safe while dealing with a flat tire.

The practical takeaway: Take 15 minutes while parked at home to locate your spare tire and verify what type it is. Check your vehicle's owner manual or look under your vehicle or in the trunk. Knowing this information before you need it removes uncertainty when facing a flat tire on the road.

Locating Your Spare Tire and Essential Tools

Your spare tire's location depends on your vehicle's make, model, and year. Knowing where to find it is essential before you're stuck on the side of the road. In many sedans and smaller vehicles, the spare is mounted under the trunk floor, accessed by removing a carpet or panel. You'll typically find a small handle or bolt that you turn to lower the spare using a cable mechanism. Some trucks and SUVs have spares mounted on the outside of the vehicle—either on the rear bumper, the side of the cargo bed, or attached to the back doors. Minivans and larger vehicles sometimes store spares in a compartment accessible from inside the cabin.

Learn About Mac Sync Options and Features →

Locating your spare is just the beginning. You'll also need several tools to remove your flat tire and install the spare. Every vehicle should have a jack—a mechanical device that lifts your car so you can remove the wheel. Most vehicles come with a scissor jack or a bottle jack, both of which operate by turning a handle or screw mechanism. You'll also need a lug wrench, which has four sides designed to fit different lug nut sizes. This tool loosens and tightens the nuts that hold your wheel onto the vehicle. Many vehicles come with a wrench that fits their specific lug nuts, though universal wrenches are available.

Beyond the jack and wrench, having a wheel wedge or wooden block helps prevent your vehicle from rolling while it's on the jack. Some guides recommend keeping wheel wedges in your vehicle. You should also know where your vehicle's jack points are located—specific reinforced spots on the frame designed for jacking. Using the wrong spot can damage your vehicle or cause the jack to slip. Your owner's manual shows the exact jack points. Additionally, keeping a flashlight, work gloves, and a small first aid kit in your vehicle can make the experience safer and more manageable, especially if you experience a flat after dark.

Practical takeaway: Open your trunk or check under your vehicle right now and verify you have a jack, lug wrench, and spare tire present. If any tools are missing or appear damaged, replace them before you need them. Write down the location of your jack points and keep a note in your glove compartment for reference.

Step-by-Step Tire Replacement Procedure

Replacing a spare tire follows a logical sequence of steps. Learning these steps beforehand means you'll know what to expect and can work through the process methodically rather than panicking. Before you begin, ensure you're in a safe location. If your tire fails on a highway, drive slowly with your hazard lights on to reach a flat, stable area away from traffic—a parking lot, rest area, or wide shoulder. Turn off the engine and engage the parking brake. If you have reflective triangles or a warning light, place it behind your vehicle to alert other drivers.

Free Guide to Understanding Capacitor Service Options →

The first step is removing the hubcap or wheel cover if your vehicle has one. Some pop off easily by hand; others require gentle prying with the flat end of your lug wrench. Next, you'll use the lug wrench to loosen the lug nuts while the tire is still on the ground. This is important because it's easier to loosen them when the wheel isn't spinning freely in the air. Loosen them perhaps one-quarter turn—you don't need to remove them completely yet. Now position your jack under the vehicle's jack point nearest to the flat tire. The jack point is a reinforced section of the frame; never attempt to jack from the bumper or other areas.

Slowly pump or crank the jack to raise the vehicle until the flat tire is about six inches off the ground. Once elevated, completely remove the lug nuts—place them in a safe location where they won't roll away. You might set them in the hubcap or a small container. Now pull the flat tire toward you firmly to remove it from the wheel hub. The tire may be heavier than expected, so prepare yourself. Set the flat tire aside in a safe spot where it won't tip or roll. Position the spare tire in front of the wheel hub and push it onto the lug bolt studs, aligning the holes. The spare should fit snugly onto the hub.

Reinstall the lug nuts by hand first, threading them as much as possible. Once you've hand-tightened them, use the lug wrench to tighten them further in a crisscross pattern—this ensures even pressure around the wheel. Don't over-tighten; a firm, snug pressure is sufficient. Lower the vehicle back to the ground by slowly releasing the jack. Once the tire touches the ground completely, do a final tightening of the lug nuts in the same crisscross pattern. Replace the hubcap if you have one. Finally, gather your tools and the flat tire, stow them safely in your vehicle, and proceed to a tire repair shop or your destination.

Practical takeaway: If possible, practice the jacking process in your own driveway before you experience a real flat. This familiarization removes uncertainty and builds confidence. Don't actually remove the tire during practice—just get comfortable with how the jack operates and where it should be positioned.

Different Spare Tire Types and Their Limitations

Not all spare tires function identically, and understanding your vehicle's spare type affects how you'll use it after replacement. Temporary spare tires, often called donuts, are the most common type on modern vehicles. These smaller, lighter wheels and tires are designed to reduce vehicle weight and save trunk space. However, they come with strict limitations. Temporary spares should only be driven at speeds of 50 miles per hour or less, and typically only for 70 miles or fewer. The tread pattern and construction differ from regular tires, making them unsuitable for extended driving. If you're far from a tire shop when you experience a flat and install a temporary spare, plan to drive directly to the nearest tire repair facility rather than continuing your normal journey.

Get Your Free Local Massage Deals Guide →

Full-size spare tires are identical to your regular tires and are the ideal option when you need a replacement. You can drive at normal speeds and continue your regular activities without restriction. However, if the full-size spare is a different brand or has significantly different wear than your other tires, it may affect your vehicle's handling and traction. Some vehicle owners prefer replacing the flat tire with the spare and then having the flat professionally repaired later, rather than installing a mismatched tire long-term. This depends on whether your spare matches your other tires and your personal driving needs.

Run-flat tires are designed with reinforced sidewalls that allow the tire to continue functioning even after a puncture for a limited distance, typically up to 100 miles at reduced speed. If you have run-flat tires, you won't need to replace a damaged tire immediately, but you should still drive