Get Your Free Spare Tire Changing Guide

Understanding Your Vehicle's Spare Tire System

Every vehicle comes equipped with a spare tire, but many drivers have never examined theirs or understood how it works. Your spare tire is a critical safety component that allows you to continue driving when one of your main tires becomes damaged or loses air pressure. According to the National Highway Traffic Safety Administration (NHTSA), approximately 11 million tire-related vehicle failures occur annually in the United States, making spare tire knowledge essential for all drivers.

Learn About Alkaline Food Options and Nutrition →

There are three main types of spare tires found on modern vehicles. Full-size spares are identical to your regular tires and provide a complete replacement. Temporary or "donut" spares are smaller, lighter wheels designed to get you to a repair shop—they typically shouldn't be driven more than 70 miles or at speeds exceeding 50 miles per hour. Some vehicles use run-flat tires, which have reinforced sidewalls that allow continued driving even after a puncture, though at reduced speeds.

Your spare tire is usually stored in one of several locations depending on your vehicle type. Sedans and hatchbacks typically keep the spare beneath the trunk floor. SUVs and trucks often mount the spare on the rear bumper or underneath the vehicle. Some luxury and compact vehicles store the spare inside the vehicle itself. Knowing where your spare is located is the first step in being prepared for a roadside emergency.

The condition of your spare tire matters significantly. Even though it sits unused most of the time, spare tires can lose air pressure gradually—studies show they can lose 1-2 PSI (pounds per square inch) per month. Before any long road trip, check your spare tire's air pressure using a tire gauge. The correct pressure is printed on a label inside your driver's door jamb or in your owner's manual. A properly maintained spare tire is your best insurance against being stranded.

Practical Takeaway: Locate your spare tire today and verify its condition. Check the air pressure with a tire gauge and compare it to the recommended PSI listed in your owner's manual. Write down where your spare is stored so you can find it quickly in an emergency situation.

Gathering the Right Tools and Equipment

Before you need to change a tire, you should know what tools are required and where to find them. Most vehicles come with a basic tire-changing kit that includes several essential items. A lug wrench is a metal tool used to loosen and tighten the nuts that hold your wheel in place. Most vehicles include a four-way lug wrench, which has different socket sizes on each end to fit various lug nut sizes. A jack—a mechanical device that lifts your vehicle—is also included with nearly every new car. Many newer vehicles include scissor jacks, which are compact and relatively easy to operate.

Your Free Beginner's Makeup Application Guide →

Beyond the basic equipment that typically comes with your vehicle, having additional tools on hand is practical. A flashlight or work light is invaluable if you experience a tire problem at night or in low-light conditions. According to the NHTSA, approximately 24% of vehicle breakdowns occur between 6 PM and 6 AM. A pair of work gloves protects your hands from dirt and sharp objects. A wheel wedge or block prevents your vehicle from rolling while it's elevated. Heavy-duty blocks or bricks can serve this purpose if you don't have a commercial wedge.

Where should you store these tools? Keep your lug wrench and jack in an easily accessible location in your vehicle—ideally in the trunk or under a rear seat. If your vehicle didn't come with these items or they've gone missing, you can purchase them at any automotive parts store for reasonable prices. A basic lug wrench costs between $10-25, and a portable jack ranges from $30-100 depending on the type and weight capacity needed for your vehicle.

Having a tire repair kit on hand provides additional options. Tire plug kits, which cost under $10, allow you to patch small punctures temporarily. These kits typically include rubber strips, a reaming tool, and adhesive. Tire sealant spray (around $5-15 per can) can temporarily seal small leaks, allowing you to drive to a repair facility. However, these temporary solutions should always be followed up with professional tire service—they're meant to get you safely off the roadside, not to be permanent fixes.

Practical Takeaway: Check your vehicle's trunk or storage areas to locate the lug wrench and jack that came with your vehicle. Test that you can operate the jack by placing it under a safe lifting point (not under the fuel tank or plastic trim) and raising it slightly. If these tools are missing, purchase replacements from an automotive store.

Preparing Yourself and Your Vehicle for a Safe Tire Change

When you experience a tire problem, your immediate response significantly affects your safety. If you're driving on a highway or busy road and notice a tire issue, don't slam on your brakes. Instead, gradually slow down and carefully move toward the shoulder or a safe, flat area away from traffic. Activate your hazard lights (also called 4-way flashlights) to alert other drivers that you're stopped. The Federal Highway Administration reports that being struck by another vehicle is the leading cause of deaths in roadside work zones.

Get Your Free Guide to Phone Charging Laptop Basics →

Once you're in a safe location, take several minutes to assess the situation before beginning work. Turn off your engine and ensure your vehicle is on level, firm ground—never attempt a tire change on soft shoulder areas, sand, or gravel. Avoid changing tires in heavy rain, fog, or other conditions that reduce visibility. If conditions are unsafe, it's better to call for roadside support services. Most vehicle owners have access to roadside assistance through their insurance company, vehicle warranty, or membership in organizations like AAA.

Before you start working, gather all your tools and supplies and lay them out nearby. This prevents you from searching for items while you're in an exposed position. Put on your work gloves and ensure you're wearing closed-toe shoes with good traction. If it's nighttime, position your flashlight so it illuminates your work area. Place your wheel wedges or blocks behind the wheel diagonally opposite the one you're changing—if you're changing a front-right tire, place wedges behind the rear-left wheel.

Understanding your vehicle's anatomy is important for safe tire changes. Never place the jack under plastic trim pieces, fuel tanks, or suspension components. Your vehicle's owner's manual shows specific jacking points—these are reinforced areas designed to support your vehicle's weight. Most vehicles have clearly marked jacking points on the frame near each wheel. Look for a small notch or raised area on the vehicle's rocker panel (the lower side of the body between the front and rear wheels). This is where the jack's saddle should fit.

Practical Takeaway: Review your vehicle's owner's manual right now and identify the four jacking points around your vehicle. Take photos of these locations with your phone so you have visual reference. Verify that your hazard light button works and practice activating it. If you don't have wedges, identify items you could use (heavy rocks, bricks, or wooden blocks) and keep them in your vehicle.

Step-by-Step Tire Changing Process

The actual process of changing a tire follows a logical sequence that helps ensure safety and efficiency. This guide walks through each step so you understand the procedure before you're on the roadside. The first step is removing the wheel cover or hubcap if your vehicle has one. Some wheel covers simply pop off by hand, while others use clips that require gentle prying with a flat tool. Place the cover aside in a safe spot where it won't get dirty or damaged. Never throw it into the road or grass where you might lose it.

How to Make Hard Boiled Eggs in an Air Fryer →

Next, loosen the lug nuts before you lift the vehicle. This is an important safety principle—it's much easier to loosen them while the wheel is on the ground and your vehicle is stable. With your lug wrench, turn each lug nut counterclockwise one-half to one full turn. You're not removing them completely yet, just breaking the seal. Apply steady pressure rather than jerky motions. If a lug nut is very tight, you can place your foot on the lower end of the lug wrench to apply more leverage, but don't stand on the wrench—this could cause injury if it suddenly gives way.

Now position your jack under the appropriate jacking point. Lower your vehicle's windows and doors, then align the jack saddle with the jacking point on the frame. Turn the jack handle clockwise to begin raising your vehicle. Raise it