Get Your Free Shokz OpenFit Pairing Guide

Understanding Shokz OpenFit: What This Guide Covers

The Shokz OpenFit pairing guide is a free informational resource that walks you through connecting your Shokz OpenFit earbuds to various devices. Shokz, formerly known as AfterShokz, manufactures bone conduction audio devices that have gained popularity since their introduction to the consumer market in 2012. The OpenFit model represents their open-ear audio technology, which delivers sound through vibrations on the bones near your ears rather than traditional speaker drivers placed inside the ear canal.

Get Your Free Jewelry Cleaning Guide With Baking Soda →

This guide provides step-by-step instructions for pairing your OpenFit earbuds with smartphones, tablets, computers, and other Bluetooth-enabled devices. Pairing is the process of connecting two Bluetooth devices so they can communicate with each other wirelessly. When you pair your OpenFit earbuds with a device for the first time, they establish a secure connection that allows them to communicate automatically in the future.

Understanding the pairing process matters because successful pairing determines whether you can use your earbuds to listen to music, take calls, or access voice commands on your devices. The guide addresses common scenarios, including pairing with your primary device, switching between multiple devices, and troubleshooting connection issues that may arise.

The information in this guide applies specifically to the OpenFit model. While other Shokz products follow similar pairing procedures, each model may have slight differences in button placement, light indicators, or menu navigation. The OpenFit uses a straightforward pairing method that takes approximately two to three minutes to complete on most devices.

Practical Takeaway: Before you begin pairing, locate your OpenFit earbuds, ensure they are fully charged (a full charge typically lasts eight to ten hours), and have the device you want to pair nearby with Bluetooth enabled.

Initial Setup and Putting Your OpenFit Earbuds Into Pairing Mode

The first step in using your Shokz OpenFit earbuds involves putting them into pairing mode, which makes them discoverable to other Bluetooth devices. The earbuds arrive from the manufacturer with a pre-installed battery, so you should be able to power them on immediately without waiting for a charge.

Get Your Free CHAMPVA Information Guide →

To enter pairing mode, hold down the main power button on the right earbud for approximately eight seconds. You will observe visual feedback through LED light indicators. Initially, the lights may show a solid color indicating the earbuds are powering on. After continuing to hold the button, the lights will begin blinking in a specific pattern—typically an alternating blue and white flash. This blinking pattern signals that the earbuds have entered pairing mode and are ready to receive a connection from a nearby device.

During pairing mode, the OpenFit earbuds will remain discoverable for roughly five minutes before automatically returning to normal mode. This time window gives you sufficient opportunity to locate the earbuds in your device's Bluetooth settings and complete the connection. If the five-minute window expires without a successful pairing, you can repeat the process by holding the power button again.

The charging case that accompanies your OpenFit earbuds serves multiple functions. It stores the earbuds when not in use, charges them through physical contact with charging pins inside the case, and can extend your total listening time throughout the day. The case itself is rechargeable via a USB-C cable, which typically delivers a full case charge in about ninety minutes.

Some users report that their earbuds were previously connected to another device before they received them. If this occurs, you may need to reset the earbuds to clear previous pairings. A factory reset typically involves holding the power button for fifteen to twenty seconds until the lights display a specific pattern indicating a reset has occurred. Consult the physical documentation that came with your earbuds for the exact reset sequence, as this can vary by manufacturing batch.

Practical Takeaway: Write down the specific LED light patterns you observe during power-on, pairing mode, and reset. This visual reference will help you quickly identify the status of your earbuds during future troubleshooting without needing to reference the guide repeatedly.

Pairing With Smartphones and Tablets

Pairing your Shokz OpenFit earbuds with a smartphone or tablet is one of the most common uses for this device. The process differs slightly between Android devices and iOS devices, though the fundamental steps remain similar. Both operating systems use Bluetooth as the underlying technology, but the menu structures and settings locations vary.

Get Your Free Penske Truck Rental Location Guide →

For iPhone or iPad users, the process begins by opening the Settings app on your device. Navigate to the Bluetooth section—this is typically located in the main Settings menu. Ensure that Bluetooth is switched on; you will see the Bluetooth icon in the top status bar when it is active. Once Bluetooth is enabled, your device will begin scanning for nearby Bluetooth devices. This is when you should ensure your OpenFit earbuds are in pairing mode with the blinking LED lights visible.

After a few seconds of scanning, the name "Shokz OpenFit" or similar identifier should appear in the list of available devices. Tap on this entry, and your iPhone or iPad will initiate a connection. A prompt may appear asking whether you want to pair with the device. Select "Pair" or "Connect" to complete the process. Once paired, you should see "Connected" appear beneath the device name. Future connections to this iPhone or iPad will occur automatically when you turn on the earbuds and bring them near the phone.

Android device users follow a comparable procedure. Open Settings, navigate to Connected Devices or Bluetooth (the exact menu name varies by manufacturer and Android version), and enable Bluetooth. The OpenFit earbuds should appear in the list of available devices. Tap the device name to initiate pairing. Some Android phones may display a numeric code to verify the connection; simply confirm this code matches on both devices if prompted.

Tablets from both Apple and Android manufacturers use the same pairing procedures as their smartphone counterparts. The primary difference is that tablet screens are typically larger, making menu navigation slightly easier. Once paired, your earbuds will remember this tablet and reconnect automatically when you bring them nearby with Bluetooth enabled.

Practical Takeaway: After your first successful pairing with a phone or tablet, the earbuds will automatically reconnect to that device whenever they are powered on and within Bluetooth range (typically thirty to forty feet indoors). You do not need to repeat the manual pairing process unless you reset the earbuds or specifically unpair them from that device.

Pairing With Computers and Other Devices

Many users want to pair their Shokz OpenFit earbuds with computers for video calls, online meetings, or listening to music while working. Both Windows and macOS computers support Bluetooth connectivity, and the pairing procedure on computers mirrors the process used on phones and tablets, though the menu locations differ.

Learn About the Mavis Tire Credit Card →

Windows computer users should click the Windows Start button and open Settings. Navigate to Devices, then Bluetooth and Other Devices. Make sure Bluetooth is turned on. Your Windows computer will then scan for nearby Bluetooth devices. With your OpenFit earbuds in pairing mode, they should appear in the list within several seconds. Click on "Shokz OpenFit" or the corresponding name, and select "Pair" from the options that appear. Windows will establish the connection and may play a confirmation sound through your default audio device.

macOS users follow a similar path. Click the Apple menu in the top-left corner, select System Preferences or System Settings (depending on your macOS version), and navigate to Bluetooth. Ensure Bluetooth is enabled by checking for an "On" indicator. With your OpenFit earbuds in pairing mode, they should appear in the list of available devices. Select the OpenFit entry and click "Connect." Your Mac will complete the pairing process.

After pairing with a computer, you may need to configure your audio settings to use the OpenFit earbuds as your default audio output device. On Windows, right-click the speaker icon in the system tray and select your audio device. On macOS, go to System Preferences, select Sound, and choose the OpenFit earbuds from the Output tab. These settings determine where audio will be routed when you play music, watch videos, or join video calls.

Gaming consoles, smartwatches, and car infotainment systems can also connect to your OpenF