Get Your Free Prehung Door Installation Guide

Understanding Prehung Door Basics and Installation

A prehung door is a door unit that arrives at your home already assembled into its frame, with hinges and the door itself attached. Unlike hollow-core or solid-core doors that come separately, prehung doors are factory-mounted and ready for installation into your wall opening. This guide covers the fundamental information about how prehung doors work and what to expect during the installation process.

Learn About ATV Insurance Coverage Options →

According to the National Association of Home Builders, prehung doors account for approximately 60% of residential door replacements because they reduce on-site assembly work. The door comes with the frame (called a jamb), the door slab, hinges already mounted, and typically includes the doorstop and weatherstripping. This means much of the technical alignment work is completed before delivery to your home.

Understanding the components helps you recognize what you're working with. The jamb consists of three pieces: two vertical sides and one horizontal top piece. The hinges are pre-installed, usually three on standard doors. The threshold sits at the bottom in exterior doors. Interior prehung doors typically weigh between 40 and 80 pounds, while exterior doors weigh 80 to 150 pounds depending on material and whether they contain glass or have solid construction.

The installation process involves five main steps: preparing the opening, positioning the door unit, shimming (adjusting with small wooden wedges), securing the frame, and installing trim. The entire process typically takes 2 to 4 hours for a standard doorway, though this varies based on existing conditions and your familiarity with basic tools.

Practical Takeaway: Before beginning installation, measure your existing opening carefully. Prehung doors come in standard sizes (32", 36", 42" widths for most interior doors), and the rough opening should be approximately 1 to 1.5 inches wider and taller than the door frame itself to allow for proper shimming and adjustment.

Tools and Materials You'll Need

Successful prehung door installation requires specific tools, most of which are common household items or available for rent. The cost of assembling these tools typically ranges from $50 to $200 if you don't already own them, and many can be repurposed for future projects around your home.

Learn About Driver's License Suspension Status →

Essential tools include a level (a 24-inch spirit level is standard), shims (wooden wedges sold in bundles at hardware stores for $3 to $8), a hammer or drill, screws or nails designed for door frames, a handsaw or power saw for trimming shims, and a utility knife. A cordless drill-driver is helpful but not required. For measuring, bring a tape measure and consider using a stud finder if you need to locate existing framing. Safety equipment should include work gloves and safety glasses.

Materials needed beyond the prehung door itself include the shims mentioned above, fasteners appropriate for your wall type (wood screws for wooden frames, special fasteners for metal studs), caulk or sealant, and possibly trim pieces if you're finishing the installation. If you're replacing an existing door, you'll need a pry bar or reciprocating saw to remove the old unit. Door frame fasteners should be 2.5 to 3 inches long to penetrate through the frame and adequately into the wall framing.

Hardware stores typically provide free advice on tool selection and rental options for items like power saws or nail guns. Many locations have rental departments where you can borrow specialized tools for $10 to $25 per day. Purchasing a basic homeowner tool kit ($40 to $80) can be economical if you plan multiple projects.

The quality of your shims matters significantly. Premium cedar shims cost slightly more but resist warping better than lower-quality alternatives. Budget approximately $15 to $30 for shims, level, fasteners, and sealant combined.

Practical Takeaway: Purchase shims and fasteners only after you've received your prehung door and assessed your specific wall type. Different wall constructions (standard 2x4 wood framing, steel studs, concrete block) require different fastening approaches, so having the door unit present allows you to choose appropriate materials.

Preparing Your Doorway Opening

Proper preparation of your existing doorway determines whether your prehung door will hang level, close smoothly, and seal properly. This step requires careful measurement and potentially removing an existing door if you're replacing one. According to installation data from major door manufacturers, approximately 30% of installation problems stem from inadequate opening preparation rather than installation errors.

Learn About Senior Energy Discount Programs →

Start by measuring your rough opening—the space where the door frame will sit. Measure the width at the top, middle, and bottom; measure the height at the left, center, and right. Standard prehung doors have specific opening requirements, usually 1 to 1.5 inches larger than the door frame dimensions. If your opening is too small, you'll need to carefully remove drywall or framing. If it's too large, you can adjust the frame position using shims, but severely oversized openings may require rebuilding part of the wall.

Remove any existing door using a pry bar, working carefully to avoid damaging surrounding walls. Take photos before removing the old door to help you understand how the frame was positioned. Look for nails or screws holding the frame, and remove these methodically. If the opening has been caulked or painted closed, use a utility knife to cut through sealant before prying.

Inspect the opening edges for level and plumb (vertical straightness). Use your level to check if the side jambs are truly vertical and the head jamb is horizontal. If the opening is significantly out of plumb—more than 1/4 inch over the door height—you have two options: shim aggressively to compensate, or remove additional wall material to create a properly aligned opening. Most installers can work with slightly imperfect openings using shims, but severely misaligned openings cause operational problems.

Clean the opening thoroughly. Remove old caulk, paint drips, or debris that could prevent the frame from sitting flush. Smooth any rough edges with sandpaper or a utility knife.

Practical Takeaway: Create a detailed sketch showing your opening measurements and check them against your prehung door specifications before installation day. Most door manufacturers provide installation guides showing exact opening dimensions needed; having this documented prevents wasted trips to the hardware store.

The Installation Process Step-by-Step

The actual installation of a prehung door follows a logical sequence that ensures proper alignment and function. This section walks through each stage with information about what to expect and what adjustments may be necessary during installation.

Free Guide to Home Weatherization Resources →

Begin by positioning the door frame in the opening. For exterior doors, many installers use shims along the bottom to create a slight slope (about 1/8 inch drop from inside to outside) that helps water drain away. Insert the frame into the opening and check the head jamb (top piece) for level using your spirit level. The bubble should sit centered in the level tube when the frame is properly aligned. If the opening floor is uneven, the side jambs may need to be plumb (vertical) even if the head appears slightly tilted; prioritize plumb on vertical elements.

Insert shims from the outside at hinge locations—typically 12 inches from the top, 12 inches from the bottom, and at mid-height. Shims work in pairs (two wedges facing opposite directions) and should be inserted until they're snug but not hammered in excessively, as over-shimming can bow the frame. After inserting shims, check that the door closes smoothly and doesn't bind on the frame. Gaps between the door edge and frame should be consistent—approximately 1/8 inch is standard.

Once alignment is satisfactory, secure the frame with fasteners. Drill pilot holes through the frame into the wall framing to prevent splitting. Use screws rather than nails when possible, as screws can be removed if adjustment becomes necessary. Install fasteners at each shim location and at least one additional fastener between shim locations. Exterior doors typically require fastening every 12 to 16 inches around the perimeter.

Before finishing, verify door operation multiple times. The door should swing freely, close completely without forcing, and latch properly. If the door binds or doesn't close smoothly, loosen fasteners slightly and adjust shims rather than