Get Your Free Pool Gallons Calculation Guide

Understanding Pool Volume and Why It Matters

Knowing how many gallons of water your pool holds is one of the most important pieces of information you can have as a pool owner. This measurement affects nearly every decision you make about pool maintenance, from how much chlorine to add, to the size of pump and filter system you need, to how long it takes to fill or drain your pool. Without an accurate gallon count, you might add too much or too little chemical treatment, which can lead to cloudy water, algae growth, or skin irritation for swimmers.

Learn About Foods for Pancreatitis Management →

The Environmental Protection Agency reports that the average residential swimming pool contains between 12,000 and 25,000 gallons of water, though this varies widely depending on pool size and shape. Some small above-ground pools might hold only 3,000 gallons, while larger in-ground pools can contain 50,000 gallons or more. Even a difference of a few thousand gallons can significantly impact your maintenance routine and chemical dosing.

Every pool maintenance product you purchase includes dosing instructions based on pool volume. For example, a chlorine tablet might say "add one tablet per 10,000 gallons per week." If you don't know your actual pool volume, you're essentially guessing at the right treatment amount. Too little chlorine and bacteria and algae can grow unchecked. Too much and you risk over-chlorination, which creates harsh chemical smell and can irritate eyes and skin.

Beyond chemicals, your pool volume determines what size equipment you need. Your pump circulation rate is measured in gallons per hour, and pool professionals recommend that all water should cycle through your filter at least once every 24 hours. This is called the turnover rate. If you underestimate your pool volume, you might buy a pump that's too small, resulting in inadequate water circulation and filtration.

Takeaway: Calculating your pool volume accurately is the foundation of proper pool care. This single measurement influences your entire maintenance budget and routine, making it worth taking time to get right.

Calculating Volume for Rectangular and Square Pools

Rectangular and square pools are the easiest shapes to measure and calculate. The basic formula is straightforward: length times width times average depth, then multiply by 7.5 to convert cubic feet to gallons. This works because water fills a space with a specific volume, and that volume can be measured in three dimensions.

Learn About SSDI Application Forms and Process →

To measure your rectangular pool, you'll need a tape measure or measuring wheel. Start by measuring the length of the pool from one end to the other at the water line, not at the top edge of the pool wall. Do the same for the width. These measurements should be in feet, though you can measure in feet and inches and then convert. For example, if your pool is 20 feet 6 inches long, convert that to 20.5 feet.

Next, measure the depth at the deepest point and the shallowest point. Most residential pools have varying depth—shallower at one end and deeper at the other. If your pool is 3 feet deep at the shallow end and 5 feet deep at the deep end, your average depth is 4 feet. This is the number you'll use in your calculation. If your pool has a consistent depth throughout, you only need to measure once.

Here's a worked example: Your pool measures 20 feet long, 15 feet wide, with an average depth of 3.5 feet. The calculation would be: 20 × 15 × 3.5 = 1,050 cubic feet. Then multiply by 7.5: 1,050 × 7.5 = 7,875 gallons. This is a reasonable size for many residential pools. The multiplication by 7.5 is a standard conversion factor because one cubic foot of water equals 7.48052 gallons, which rounds to 7.5.

For square pools, the math is even simpler since length and width are the same. A 15-foot by 15-foot square pool with an average depth of 4 feet would calculate as: 15 × 15 × 4 × 7.5 = 6,750 gallons. Keep in mind this method assumes straight sides and a flat bottom, which is true for most above-ground and many in-ground pools.

Takeaway: For rectangular and square pools, write down three measurements—length, width, and average depth—then use the formula length × width × depth × 7.5. Double-check your depth measurement since it's often the number most likely to be estimated incorrectly.

Calculating Volume for Circular and Oval Pools

Circular and oval pools require a slightly different calculation because they don't have four equal sides. The math uses the area of the circle or oval as the starting point. For a circular pool, you'll use the formula: radius squared times 3.14 times average depth times 7.5. For an oval pool, the calculation is a bit more complex, but still manageable with basic measurements.

Free Shinco Air Conditioner Owner's Guide →

To measure a circular pool, find the diameter by measuring straight across the center of the pool at the water line. If your pool is 18 feet across, the radius is half of that, or 9 feet. Then square the radius: 9 × 9 = 81. Multiply by 3.14 (pi, the mathematical constant used for circles): 81 × 3.14 = 254.34. Then multiply by your average depth and 7.5. If the pool is 4 feet deep: 254.34 × 4 × 7.5 = 7,630 gallons.

Oval pools are common in modern residential settings. To measure an oval pool, find the length (the longer dimension measured through the center) and the width (the shorter dimension measured through the center). Then measure the average depth as you would for any pool. The formula is: length × width × 0.89 × average depth × 7.5. The 0.89 is a correction factor that accounts for the shape of an oval.

Example: An oval pool that is 30 feet long and 20 feet wide with an average depth of 3.5 feet would calculate as: 30 × 20 × 0.89 × 3.5 × 7.5 = 13,817 gallons. This is a realistic size for a medium-to-large residential pool. The 0.89 factor is important—without it, you'd overestimate the volume by about 11 percent.

Many pool owners keep these formulas written down near their equipment or on a small note card stored with pool maintenance supplies. This way, if you need to recalculate after making any changes to your pool—perhaps after resurfacing that affects depth—you have the information readily available. Some people also take photos of their measurements to reference later.

Takeaway: For circular pools, measure the diameter and depth, then use: (radius² × 3.14 × depth × 7.5). For oval pools, measure length, width, and depth, then use: (length × width × 0.89 × depth × 7.5).

Accounting for Special Pool Shapes and Features

Not all pools are simple geometric shapes. Many modern pools have irregular designs, curved edges, attached spas, or sloped bottoms that make volume calculation more challenging. However, you can still arrive at a reasonable estimate by breaking the pool into simpler sections and calculating each part separately.

Get Your Free Mobile Banking Security Guide →

For a pool with a kidney-shaped or freeform design, try to mentally divide it into sections. Perhaps you can see it as two circles of different sizes connected together, or as a rectangle with curved sections. Calculate the volume of each section using the appropriate formula, then add them together. This approach won't be perfectly precise, but it will be much more accurate than guessing.

Attached spas or hot tubs need to be calculated separately from the main pool. Many pool owners want to know the combined total gallons for chemical purposes, but also want to know the spa volume separately since spas often require different maintenance than pools. A typical residential spa holds between 300 and 800 gallons. If your spa is 8 feet in diameter and 2.5 feet deep on average, it would calculate as a circular pool: (4² × 3.14 × 2.5 × 7.5) = approximately