Get Your Free Maytag Dishwasher Filter Cleaning Guide

Understanding Your Maytag Dishwasher Filter System

Your Maytag dishwasher contains a filtration system that works to trap food particles, debris, and other materials during the wash cycle. This system is essential for keeping your dishes clean and preventing damage to the dishwasher's internal components. The filter assembly typically consists of two main parts: a fine filter screen and a coarse filter basket. These components work together to catch particles of different sizes, preventing them from recirculating onto your dishes or clogging the spray arms and pump.

Learn About Business EIN Numbers →

The fine filter screen is the primary barrier against small particles. It has tiny perforations that allow water to pass through while trapping food debris. The coarse filter basket sits beneath or around the fine filter and catches larger food particles before they reach the fine filter. Understanding how these two components work together helps you maintain them more effectively.

Most Maytag dishwasher models have the filter assembly located at the bottom of the tub, typically in the center or toward the back. The exact location and configuration can vary depending on your specific model year and design. Some models feature a manual filter system that requires regular cleaning, while others may have semi-automatic or fully automatic systems that grind up food waste.

When filters become clogged with debris, water cannot circulate properly through the dishwasher. This leads to poor cleaning performance, spots on dishes, and potential damage to the pump motor over time. Regular filter maintenance is one of the most important preventive steps you can take to keep your dishwasher functioning optimally and extending its lifespan. Many households report that their dishwashers perform significantly better once they establish a regular filter cleaning routine.

Practical Takeaway: Locate your dishwasher's filter assembly by consulting your user manual or checking the bottom center of the tub. Take a photograph of the filter system so you can reference it when cleaning or troubleshooting.

How to Access and Remove Your Dishwasher Filter

Accessing your Maytag dishwasher filter is a straightforward process that requires no special tools or technical skills. Begin by ensuring your dishwasher is completely empty and that no cycle is running. Open the dishwasher door fully and look at the bottom of the tub. Most filters are located in the center or slightly toward the rear of the interior floor.

Free Guide to Child Support Law Changes →

The filter assembly typically consists of a cylindrical or basket-shaped component that can be lifted straight up or twisted counterclockwise to remove. Before attempting removal, rinse away any loose debris from the top of the filter with warm water from your sink. This prevents larger particles from falling into the sump area below the filter when you remove it.

To remove a twist-lock style filter, grip the top of the filter assembly firmly with both hands. Apply steady pressure and rotate it counterclockwise approximately one-quarter to one-half turn until you feel resistance cease. Once unlocked, lift the filter straight up and out of the dishwasher. For lift-out style filters, simply grasp the top handle or rim and pull directly upward with moderate force.

After removal, place the filter into your sink or a basin. The filter will likely contain trapped food particles, grease, and other debris. Some filters may also have a rubber gasket or seal around the base—be careful not to damage this component during removal, as it prevents water leakage when the filter is properly reinstalled.

If you encounter resistance when trying to remove the filter, stop and do not force it. Consult your owner's manual for model-specific instructions, or check Maytag's online support resources for a visual demonstration. Forcing a stuck filter can damage the locking mechanism or gasket.

Practical Takeaway: Write down the removal instructions specific to your model in a notebook you keep near your dishwasher. This makes future cleanings faster and reduces the chance of accidentally damaging the filter assembly.

Step-by-Step Filter Cleaning Process

Once you have removed the filter assembly, the cleaning process involves several steps that progressively remove different types of buildup. Start by holding the filter under warm running tap water. Allow the water to flow through the fine filter screen from the clean side, washing away loose food particles and debris. Rotate the filter while doing this to ensure water reaches all areas of the screen.

Get Your Free Freight Broker License Information Guide →

Next, use a soft-bristled brush or an old toothbrush to gently scrub the fine filter screen. Brush in the direction of the perforations, moving from top to bottom. This helps dislodge particles that may be stuck in the tiny holes. Pay special attention to the edges and corners where debris tends to accumulate. Avoid using hard-bristled brushes or abrasive scrubbing pads, as these can damage the delicate screen material.

For the coarse filter basket, use the same warm water and soft brush technique. The larger openings in this component allow you to clean more thoroughly. If you notice stubborn buildup or grease coating, soak the filter in warm water mixed with a small amount of dish detergent for 10 to 15 minutes. This helps dissolve grease and makes removal easier. After soaking, scrub again with the soft brush and rinse thoroughly under running water.

Check for any visible damage to the filter screen or gasket during cleaning. Look for tears, cracks, or deterioration in the rubber seal. Small tears in the screen may not immediately affect performance, but they will gradually worsen and should be monitored. A damaged gasket, however, should be replaced to prevent water from bypassing the filter during operation.

If you discover mineral deposits or hard water buildup on the filter, soak it in a solution of equal parts white vinegar and warm water for 20 to 30 minutes. The acidic vinegar dissolves mineral deposits without damaging the filter materials. Scrub gently with a soft brush, then rinse thoroughly with clean water to remove all vinegar residue.

Practical Takeaway: Set a reminder on your phone or calendar to clean your filter every 2 to 4 weeks, depending on how frequently you use your dishwasher and the amount of food debris typically present.

Reinstalling Your Filter and Checking for Proper Fit

After your filter is completely clean and dry, you are ready to reinstall it. Begin by ensuring the area where the filter sits is clean and free of debris. Use a damp cloth to wipe the sump area around the filter location, removing any food particles or grease that may have accumulated during the cleaning process.

Learn About Santa Clara County Housing Programs →

For twist-lock filters, align the filter assembly with the opening in the dishwasher tub. The filter should have orientation guides or alignment tabs that prevent improper installation. Lower the filter into place and push down gently but firmly. Once seated, rotate the filter clockwise until you feel it lock into position. You should hear or feel a distinct click or catch point. Avoid over-tightening, as this can strain the locking mechanism.

For lift-out style filters, simply position the filter directly over the opening and lower it straight down until the bottom rests on the supports or rim. The filter should sit flush with the surrounding surface with no gaps or tilting. Check that any handles or tabs are properly positioned and accessible for future removal.

After installation, close the dishwasher door and run your hand around the filter top from inside the tub. The filter should not wobble or move from side to side. If it does, open the door and check that it is fully seated and locked. Improper seating allows unfiltered water to circulate directly back onto your dishes, defeating the purpose of the filter system.

Run a short rinse cycle (without dishes) to confirm that your filter is installed correctly and that no leaks are occurring. During the cycle, open the door slightly after a minute or two and check the sump area beneath the filter. You should not see water pooling or spraying from the filter edges. If water is leaking from where the filter meets the tub, stop the cycle and reinstall the filter, ensuring it is fully seated and locked.

Practical Takeaway: Before running a full wash load after filter installation, test with a rinse cycle. This catches any installation problems before your dishes or laundry could be affected by improper water circulation.

Maintenance Schedule and Long-Term Care

Establishing a regular maintenance schedule ensures your dishwas

Learn About Famous Footwear Store Credit Options →