Get Your Free Guide to Weigh Stations

What Weigh Stations Are and Why They Exist

Weigh stations are official inspection facilities operated by state transportation departments and federal highway authorities. These stations sit along major highways and interstates, usually in visible locations near state borders or at regular intervals on major trucking routes. Their primary purpose is to measure the weight of commercial vehicles and ensure they comply with federal and state weight limits.

Learn About Getting Your NJMVC Real ID Appointment →

The weight limits exist for important safety reasons. When trucks carry loads heavier than allowed, the extra weight puts dangerous stress on bridge structures, road surfaces, and the truck itself. Overloaded vehicles take longer to stop, are harder to control on curves, and are more likely to experience mechanical failures. A fully loaded semi-truck can weigh up to 80,000 pounds when operating legally. Without weight restrictions, some operators might try to cram significantly more cargo onto their vehicles to earn extra money, which would create hazards for everyone on the road.

Beyond weight checking, weigh stations serve several other functions. They inspect vehicle safety equipment like brakes, lights, and tires. They check that drivers have proper commercial licensing and that vehicles have the required insurance and registration documents. They also monitor compliance with hours-of-service rules, which limit how long drivers can operate without rest breaks. These rules prevent fatigued driving, which causes accidents.

Weigh stations are staffed by certified inspectors employed by each state's Department of Transportation or Motor Vehicle division. These inspectors have received formal training in vehicle inspection procedures and federal transportation regulations. They use calibrated scales that measure weight with precision. Some stations are open 24 hours, while others operate during business hours only, depending on traffic volume and location.

Takeaway: Weigh stations exist to protect road safety and infrastructure by ensuring commercial vehicles meet weight, equipment, and driver qualification standards.

Understanding Federal and State Weight Regulations

Weight regulations come from both federal law and individual state rules. Federal regulations, set by the Federal Highway Administration, establish maximum weights for interstate commerce. The standard federal limit is 80,000 pounds gross vehicle weight rating (GVWR) for trucks with five or more axles. This is the total weight of the truck plus its cargo. Axle weight limits are also set federally—typically 20,000 pounds per single axle and 34,000 pounds per tandem axle (two axles close together).

Your Free Snake Plant Watering Guide →

States can set their own weight limits as long as they do not exceed federal maximums. Some states allow slightly lower weights on certain road types to protect local infrastructure. For example, a state might allow 80,000 pounds on interstate highways but restrict weights to 70,000 pounds on state highways or local roads. States also set their own rules about which roads require permits for heavier loads and what paperwork must accompany oversized or overweight shipments.

Different vehicle configurations have different weight distributions across their axles. A tandem axle setup distributes weight across two axles, which spreads the load and reduces damage to roads compared to putting all weight on a single axle. This is why tandem axles can carry more total weight than single axles. Inspectors at weigh stations use specialized scales to measure weight on each axle individually, not just total vehicle weight.

Special permits allow carriers to transport loads that exceed standard weight limits in certain situations. These permits are issued by state transportation departments and typically require the carrier to show that the load cannot be split into multiple trips and that the route will not damage roads. Examples include moving large machinery, industrial equipment, or mobile homes. A permit might allow a load of 100,000 or 120,000 pounds on a specific route during specific times. The permit must be carried in the vehicle and shown at weigh stations.

Takeaway: Federal law sets baseline weight limits for interstate commerce, but individual states can establish their own rules and permit processes for overweight loads.

What Happens During a Weigh Station Inspection

When a commercial vehicle approaches a weigh station, it must enter and proceed to the scales. The process begins with the driver pulling the vehicle onto the weigh scale platform. Modern weigh stations use in-motion scales or static scales. In-motion scales measure weight as the vehicle drives over them at low speed, which is faster. Static scales require the vehicle to stop completely while the weight is measured. The scale measures the total weight of the vehicle and its cargo.

Check Your Macy's Gift Card Balance Guide →

If the weight is within legal limits and everything appears normal during initial inspection, the driver may be allowed to proceed immediately. This is called a "green light" inspection. If the weight exceeds limits or if there are visible safety concerns, the driver must pull into an inspection bay for a detailed examination. Inspectors check the vehicle's brakes, tires, lights, coupling devices, safety equipment, and structural condition. They verify that the driver has a valid commercial driver's license (CDL) and that the vehicle's registration and insurance documents are current.

During the inspection, the inspector will also check the vehicle's logbook or electronic logging device (ELD), which records the driver's hours of service. Federal law requires commercial drivers to take rest breaks and limits the number of hours they can drive consecutively. These rules reduce fatigue-related accidents. If a driver's records show violations—such as driving more hours than allowed without rest—the inspector can place the driver out of service, meaning they cannot continue operating the vehicle until they have had proper rest.

If violations are found, the inspector issues citations. These are formal notices of violations that may result in fines. Citations are issued to the driver, the vehicle's owner, or the carrier company, depending on who is responsible for the violation. Serious safety violations, such as inoperable brakes, can result in the vehicle being declared unsafe and not allowed to leave the weigh station until repairs are made. Minor violations might result in warnings or citations that can be addressed later.

Takeaway: Weigh station inspections measure vehicle weight, check safety equipment, verify driver qualifications and rest compliance, and may result in citations if violations are found.

Types of Weigh Stations and How to Locate Them

Weigh stations fall into several categories based on their function and operation. Full-service weigh stations conduct complete inspections including weight measurement, vehicle safety checks, and driver document verification. These are staffed facilities with inspectors on duty. Port-of-entry stations typically sit at state borders and function as full-service stations. Portable scales are used in some areas to conduct temporary weigh operations, often set up at specific locations on rotating schedules.

Find Emissions Inspection Stations in Your Area →

Some weigh stations are mandatory while others are discretionary. Mandatory weigh stations must be entered by all commercial vehicles of a certain size or weight. These stations typically display a "Scale Closed" or "Scale Open" sign. If the sign says the scale is open, the driver must enter. If it says closed and is lit (or displays a message), drivers of certain vehicle types may be able to bypass the station. However, this varies by state and depends on the vehicle configuration and the driver's safety record. Some states use transponder-based bypass systems where drivers with clean safety records can skip certain stations.

Finding weigh station locations is straightforward. Each state's Department of Transportation maintains lists of weigh station locations with addresses and hours of operation. The Federal Highway Administration also maintains information about major weigh stations on interstates. GPS and mapping applications frequently include weigh station locations, and many commercial trucking apps show weigh station hours and any current closures. Trucking companies typically provide their drivers with maps and information about weigh stations on their regular routes.

Mobile applications designed for commercial drivers provide real-time information about weigh station status, including whether scales are open or closed, traffic conditions, and recent inspection patterns. Some apps allow drivers to report conditions and share information with other users. This information helps drivers plan their route and timing. However, apps designed to help drivers avoid inspections are not permitted in some jurisdictions, as they potentially enable regulatory violations.

Takeaway: Weigh stations are located at predictable positions on highways and are listed on government websites and commercial trucking apps; knowing their locations helps drivers plan routes and timing.

Common Violations Found at Weigh Stations and Their Consequences

The most common violations found at weigh stations involve weight limits. Overweight violations occur when a vehicle's total weight or axle weight exceeds legal limits. These violations have escalating consequences. A vehicle that is slightly overweight might receive a warning or a citation. A vehicle that significantly exceeds weight limits—such as 10,000 or more pounds over

Get Your Free Possum Removal Information Guide →