Free Guide to Understanding Chip Seal Pavement

What Is Chip Seal Pavement?

Chip seal, also called tar and chip or chip sealing, is a pavement surface made by combining a layer of liquid asphalt binder with small stone chips. Road crews spray hot asphalt onto an existing pavement surface, then immediately spread crushed stone aggregate across the wet asphalt. A heavy roller compacts everything together, binding the chips into place. The result is a rougher, grittier surface compared to smooth hot mix asphalt.

Where to Send Your Capital One Payment →

This pavement type has been used in the United States since the early 1900s and remains common today. The Federal Highway Administration reports that chip seal is used on approximately 7 to 10 percent of paved roads in the U.S., with even higher percentages in rural areas and certain states. In some states like Arizona, California, and Texas, chip seal represents 25 to 40 percent of paved road surfaces. The technique is popular because it costs less than traditional asphalt while extending pavement life.

The pavement structure typically consists of three layers. The base layer provides foundational support and drainage. The intermediate layer, called the binder course, offers structural stability. The top layer is the chip seal surface itself, which you see and drive on. The stone chips used in chip seal vary in size but are usually between 3/8 inch and 5/8 inch in diameter. Common stone materials include granite, limestone, and trap rock.

Practical Takeaway: Understanding chip seal as a lower-cost pavement option helps explain why many local and rural roads use this material. It serves as a legitimate maintenance solution that extends road life before more expensive reconstruction becomes necessary.

How Chip Seal Installation Works

The chip seal installation process follows specific steps to ensure the pavement bonds properly and lasts as long as designed. The process begins with preparing the existing road surface. Road crews clean the pavement by sweeping or using air blowers to remove loose debris, dirt, and vegetation. In some cases, they may use a fog seal—a thin layer of diluted asphalt—to help bind existing surface particles and fill minor cracks. This preparation step is critical because a dirty surface prevents the asphalt binder from adhering properly to the base layer.

Get Your Free Marriott Bonvoy Account Guide →

Once the surface is prepared, a distributor truck applies the asphalt binder. This equipment heats liquid asphalt to approximately 300 to 350 degrees Fahrenheit and sprays it uniformly across the road at controlled rates, typically between 0.3 and 0.6 gallons per square yard. The operator must maintain consistent speed and coverage to ensure even application. Too little binder results in poor adhesion and premature failure; too much binder creates a slippery surface and allows bleeding—where excess asphalt rises to the surface.

Immediately after binder application, a chip spreader truck distributes the stone aggregate over the wet asphalt. The timing is crucial because the asphalt must remain tacky enough to hold the chips in place. Typically, stone chips are applied at rates between 200 and 300 pounds per square yard. Following chip application, a heavy pneumatic roller compacts the aggregate into the asphalt, embedding the stones and removing excess material. Some roads receive a second compaction pass to ensure proper consolidation. Excess loose chips are swept up after the asphalt has cooled and set.

Practical Takeaway: The installation process requires precise timing and equipment control. Understanding these steps explains why road closures occur during chip sealing and why fresh chip seal roads feel different—the surface is still settling during the first few days after application.

Advantages of Chip Seal Pavement

Chip seal offers several practical advantages that make it attractive for road maintenance programs. The most significant advantage is cost. Chip seal typically costs between $0.50 and $1.50 per square yard, while traditional hot mix asphalt costs between $1.50 and $3.00 per square yard. This lower cost means road agencies can treat more miles of pavement with the same budget. A county road department might use chip seal to maintain 50 miles of road for the same investment required to rebuild 15 miles with hot mix asphalt.

Get Your Free CDL Training Guide →

Chip seal extends the life of deteriorating pavement. When applied to a road showing early signs of wear, chip seal seals small cracks, slows oxidation of the existing asphalt, and delays major reconstruction by 7 to 10 years. This extended lifespan provides significant value over time. Studies by the American Society of Civil Engineers show that chip seal can extend pavement life by 6 to 8 years when applied at the right time in a road's lifecycle.

The rough stone surface of chip seal provides excellent traction, especially in wet conditions. The exposed aggregate creates texture that increases friction between tires and pavement. This makes chip seal particularly suitable for mountainous areas, curves, and roads where stopping ability is important. The stone surface also reduces hydroplaning risk compared to smooth asphalt surfaces. Additionally, chip seal reflects light differently than dark asphalt, which some studies suggest may slightly reduce urban heat island effects in populated areas.

Maintenance is relatively simple for chip seal roads. Small cracks can be sealed with liquid crack filler without removing the entire surface. If specific areas become damaged, spot repairs can target only the problem zone rather than requiring full section replacement. The pavement also allows water drainage through its porous structure, which reduces standing water and improves visibility during rain.

Practical Takeaway: Chip seal represents good value for maintaining rural and secondary roads within limited budgets while providing real safety benefits through improved traction. Many communities choose chip seal specifically because it allows them to maintain more total road mileage.

Disadvantages and Limitations of Chip Seal

Despite its advantages, chip seal has several limitations that make it unsuitable for certain applications. The most noticeable disadvantage is loose stone. During the first weeks and months after installation, stones may come loose and scatter across the road surface. This occurs because not all stones embed completely into the asphalt, particularly in areas with heavy or frequent traffic immediately after installation. Loose stones can damage vehicle windshields and paint. Some road agencies report stone loss of 10 to 20 percent during the first year. While some loose stone is normal and expected, excessive loss indicates installation problems or unsuitable base conditions.

Your Free Guide to Texas DPS Appointment Scheduling →

Chip seal performs poorly under heavy traffic loads. The continuous stress from trucks causes stones to work loose and creates rutting—permanent indentations in the pavement surface. For this reason, chip seal is typically not used on high-volume roads, interstate highways, or routes with significant truck traffic. Studies show chip seal works best on roads carrying fewer than 400 vehicles per day. Highways and urban roads carrying thousands of daily vehicles require traditional asphalt or concrete.

The rough surface creates higher rolling resistance, which some research suggests slightly increases vehicle fuel consumption compared to smooth asphalt. The noise level is also higher, with chip seal roads producing more tire noise than hot mix asphalt surfaces. This limitation makes chip seal unsuitable for residential areas, hospitals, or schools where noise reduction is important.

Chip seal requires adequate initial compaction and good base layer conditions. If the underlying pavement is too soft, severely cracked, or poorly drained, chip seal will fail prematurely regardless of installation quality. Cold weather and rain during or shortly after installation can also compromise the seal, as the asphalt binder requires warm, dry conditions to cure properly. In climates with frequent freeze-thaw cycles or heavy rain, chip seal may have shorter lifespans than in drier regions.

Practical Takeaway: Chip seal is not appropriate for all road types. Understanding its limitations explains why you'll see it primarily on rural roads rather than main highways or city streets. Its use must match the road's actual traffic volume and conditions.

Maintenance and Long-Term Care of Chip Seal Roads

Proper maintenance extends the life of chip seal pavement and prevents early failure. During the first year after installation, the main maintenance activity is managing loose stone. Road crews periodically sweep or vacuum the surface to remove stones that haven't properly bonded. This process is normal and necessary; it removes weak stones and allows traffic to help compact remaining stones. Some agencies use traffic-speed sweepers that collect loose material without damaging the embedded stones.

Understanding VA Disability Payment Charts and Benefits →

Crack sealing is the most important long-term maintenance for chip seal roads. As the pavement ages, small c