Before you pull that cord or turn that key, it helps to know what actually happens inside your Craftsman lawn mower when you try to start it. Most Craftsman mowers use one of two starting methods: a recoil pull cord or an electric starter, depending on the model and year. The basic principle remains the same—you're igniting fuel inside the engine's cylinders to create small, controlled explosions that make the crankshaft spin.
Minnesota Tenant Rights and Landlord Laws Guide →
The starting system involves several key parts working together. The spark plug creates the spark that ignites the fuel mixture. The carburetor mixes gasoline with air in the right proportions. The fuel tank holds your gasoline. The engine oil lubricates all the moving parts. The air filter prevents dirt from entering the engine. When these components aren't in good condition, starting becomes difficult or impossible. Many people assume their mower is broken when really just one part needs attention.
Craftsman has manufactured mowers across many decades, and designs vary considerably. A mower from 1985 operates differently from a 2015 model. Push mowers differ from riding mowers. Models with Kohler engines behave differently than those with Briggs & Stratton engines. This variation matters because the starting procedure for your specific mower depends on its particular setup. Checking your owner's manual—either the physical copy or a PDF version from Craftsman's website—gives you the exact steps designed for your machine.
Practical takeaway: Locate your Craftsman mower's model number (usually on a plate attached to the mower) and find the corresponding manual. This single document contains the starting procedure specifically designed for your mower, which beats guessing based on other people's machines.
Stale gasoline causes more starting problems than any other single factor. Gasoline doesn't stay fresh forever. After about 30 days in a tank, fuel begins to break down and form varnish deposits. After 90 days, the chemical composition changes enough to interfere with ignition. If your Craftsman mower sat unused all winter—or even for several months—the fuel inside is almost certainly the problem.
Understanding Free Legal Help Resources and Options →
When gasoline oxidizes and breaks down, it creates sticky residue that clogs the carburetor, fuel lines, and injectors. These deposits prevent fresh fuel from flowing through the system. The engine turns over but won't catch because the fuel mixture is weak or blocked. This is why mowers that started fine in fall often won't start in spring, despite sitting in a garage. The fuel went bad, not the mower.
Fresh gasoline for small engines should be unleaded with an octane rating between 87 and 92. Avoid cheap discount gasoline when possible—the additives and detergent packages in name-brand fuel help keep carburetors cleaner. Ethanol-blended fuel (E10, which contains 10% ethanol) is standard in most US states and works fine in Craftsman mowers, though some older models perform better on straight gasoline. E15 or higher ethanol blends should be avoided in lawn equipment.
Store fuel in a cool, dark place in an approved fuel container, not in the mower's tank for months on end. If your Craftsman mower won't start and has been sitting for more than three months, drain the old fuel completely and refill with fresh gasoline. This single step solves the problem in roughly 60% of cases involving mowers that won't start after storage.
Practical takeaway: If your mower has sat unused for more than a season, treat fuel quality as your first suspect. Drain the tank, clean or replace the fuel filter, and fill with fresh gas before trying to start.
The spark plug is a small ceramic and metal component that costs between $5 and $15, yet it's responsible for creating the electrical spark that ignites fuel inside the cylinder. When a spark plug fails or becomes fouled, the engine literally cannot fire. No spark means no combustion, and no combustion means your Craftsman mower won't start, no matter how many times you pull the cord or turn the key.
Learn How to Renew Your Delaware Driver's License Online →
Spark plugs fail for several reasons. Carbon buildup from running too rich (too much fuel, not enough air) coats the electrode with black deposits that prevent spark from jumping. Oil fouling occurs when engine oil leaks into the combustion chamber, again preventing spark. Gap erosion happens over time as the electrode materials wear away and the gap between electrodes widens too much for electricity to jump. Most spark plugs are designed to last 100 to 300 operating hours before they should be replaced.
Checking and replacing a spark plug is straightforward on most Craftsman mowers. First, locate the spark plug wire—it's the thick black cord connected to the top of the spark plug. Pull it straight off (pull the boot, not the wire itself). Use a spark plug socket and ratchet wrench to remove the old plug. Look at the electrode tip—it should be light tan or gray. Black, wet, or heavily eroded plugs need replacement. When installing a new spark plug, make sure the gap (the space between the center and side electrodes) matches your mower's specifications, usually 0.025 to 0.030 inches for Craftsman models.
Before assuming the spark plug is bad, also check the spark plug wire and connector. A cracked wire or loose connection prevents spark just as effectively as a bad plug. If the wire shows cracks or the connector feels loose when you twist it gently, replacement is needed.
Practical takeaway: If your mower cranks but won't fire, examine the spark plug. A new plug costs under $15 and takes five minutes to install. If the plug looks okay, check the wire connection next.
The carburetor's job sounds simple—mix gasoline with air in precise proportions so the fuel ignites properly inside the cylinder. In practice, the carburetor contains dozens of tiny passages, jets, and valves, all working together to create the right fuel-air mixture across different engine speeds and loads. When the carburetor gets dirty or becomes misadjusted, starting becomes very difficult.
Learn About Enclosed Scooter Street Legal Requirements →
Stale fuel causes more carburetor problems than anything else. As gasoline breaks down, it leaves sticky varnish deposits inside the carburetor's passages and jets. These deposits block the tiny openings through which fuel must flow. The result is a fuel mixture that's too lean (not enough gas), which prevents the engine from starting. Many people clean their carburetors when they should simply drain and replace the fuel.
If your Craftsman mower has fresh fuel and a good spark plug but still won't start, the carburetor likely needs cleaning. The process varies by mower model—some have easily removable bowls with accessible jets, while others require more disassembly. Carburetor cleaner (available at any hardware store for $5-$10) works well for removing varnish. Spray it through the passages, jets, and tiny ports while the carburetor is disassembled. A small wire or compressed air helps clear blocked passages.
Some Craftsman mowers, particularly older models, have an external fuel mixture screw that adjusts the carburetor's lean/rich setting. This screw is typically located on the side of the carburetor and may have a spring and washer. Adjustments here are measured in quarter-turns. Many problems blamed on "bad carburetors" are actually just mixture screws that have backed out of adjustment. Your manual specifies the correct number of turns from the seated position.
Practical takeaway: Clean the carburetor if fuel is fresh and the spark plug is good but the mower won't start. For models with external mixture screws, check that the screw is at the correct adjustment specified in your manual.
The correct way to start your Craftsman mower depends entirely on your specific model. Push mowers with pull cords operate differently from electric-start mowers. Cold starts differ from warm starts. Reading and following your mower's starting procedure prevents wasting effort on incorrect techniques.
Get Your Free Guide to Reaching State Farm Claims →
For pull-cord Craftsman mowers
This guide is for general information only and is not medical, financial, legal, or other professional advice. For decisions specific to your situation, consult a qualified professional. See our Editorial Policy.