Free Guide to Preparing Ground for Above-Ground Pools

Understanding Ground Preparation Basics for Above-Ground Pools

Installing an above-ground pool begins long before you fill it with water. The foundation you create determines how long your pool will last, how safely it operates, and whether you'll face costly damage down the road. Ground preparation is the most critical step in the installation process, yet many pool owners overlook it or rush through it.

Get Your Free Section 8 Housing Waitlist Guide →

The basic principle is straightforward: above-ground pools need level, stable, and clean ground beneath them. When a pool sits on uneven or poorly prepared soil, the water weight—which can total 15,000 to 30,000 pounds for a medium-sized pool—creates uneven pressure on the pool walls. This causes stress on the structure, potentially leading to leaks, wall damage, or even collapse in severe cases.

Different soil types behave differently under pressure. Sandy soil drains well but can shift and settle over time. Clay soil holds water and can become unstable when saturated. Loamy soil, a mixture of sand, silt, and clay, typically provides the best foundation. Understanding what type of soil you have in your yard helps you determine what preparation steps are necessary.

The pool location itself matters significantly. You'll want to choose an area that gets moderate sunlight—too much sun accelerates algae growth and water evaporation, while too little promotes algae and makes the water cold. Avoid areas under trees, as falling leaves create maintenance headaches and roots can damage the pool bottom. Stay away from low spots in your yard where water naturally collects during rain.

Ground preparation typically takes one to three days, depending on your yard size and soil conditions. The work is physically demanding but does not require specialized equipment beyond basic tools most homeowners have available. Many people successfully complete this task without professional help by following systematic steps.

Practical Takeaway: Start by selecting a location that's relatively level, away from trees, and in an area that receives moderate sun. Scout your yard several days before starting to observe how water drains after rain.

Measuring and Marking Your Pool Area

Accurate measurements prevent costly mistakes and wasted effort. Before you remove a single shovelful of soil, you need to precisely mark where your pool will sit. This step takes only an hour or two but significantly impacts the entire project.

Your Free Guide to Georgia Unemployment Claims →

First, determine your pool size. Above-ground pools come in standard sizes: 12, 15, 18, 21, 24, or 27 feet in diameter for round pools, and 10x16, 12x20, 15x24, or 18x33 feet for rectangular pools. Knowing your exact pool dimensions is essential for marking the correct area.

For round pools, find the center point of where your pool will sit. Drive a stake into the ground at this center point. Measure from this stake outward to determine your radius—for a 15-foot diameter pool, the radius is 7.5 feet. Use a string tied to the center stake, extending to the length of the radius, and walk around the perimeter while marking the circle with spray paint, flour, or garden lime. This creates a visual outline for your work area.

For rectangular pools, use the 3-4-5 triangle method to ensure your corners are true right angles. Measure 3 feet along one edge and mark it. Measure 4 feet along the adjacent edge and mark it. The diagonal distance between these two marks should be exactly 5 feet if your corner is square. Adjust your layout until all corners are square, then mark the entire perimeter.

Add an additional 2-3 feet beyond your pool outline on all sides. This extra space allows room for the pool walls to sit properly and gives you working space during installation. The total area you'll be preparing is actually larger than the pool itself—a 15-foot round pool requires preparation of approximately a 20-22 foot diameter circle.

Take photographs or make notes of your marked area. These records help you stay focused during the physical work ahead and allow you to verify that you've prepared the entire necessary zone.

Practical Takeaway: Use spray paint to mark your pool perimeter with a 2-3 foot buffer zone around all sides. Double-check all measurements before beginning any excavation work.

Removing Debris and Vegetation

Before leveling, you must clear away everything that could puncture or damage your pool. This includes rocks, sticks, roots, and vegetation. The pool's vinyl or wall material sits directly on top of this prepared ground, so even small sharp objects can create holes or weak spots.

Free Guide to Email Setup Troubleshooting Tips →

Start by removing all vegetation within your marked area. Use a shovel or garden spade to cut away sod and grass, removing it to a depth of about 2-3 inches. If you have a sod cutter—available for rent from most equipment rental companies for about $50-$75 per day—this job goes much faster. Set the sod aside; you can compost it or use it to patch other areas of your yard.

Once vegetation is removed, inspect the exposed soil carefully for rocks and debris. Remove all visible rocks larger than 1 inch in diameter. Pay special attention to areas where previous construction occurred or where trees once stood, as these locations often contain hidden rocks and buried wood. Work methodically across the entire prepared area, breaking up compacted soil as you go and removing stones as you find them.

Look for and remove all root systems, especially from trees near your pool area. Living roots can grow through your pool bottom, and dead roots create air pockets that cause uneven settling. If you find a large root system, you may need to remove the tree or at minimum dig out as much of the root system as possible. For small woody debris and root fragments less than 1 inch in diameter, you can leave these in place as they won't significantly affect the foundation.

Some homeowners rent a magnetized rake, which helps pull smaller metal debris from the soil. While this may seem excessive, it's worthwhile if your property has a history of metal debris from previous construction or vehicle parts.

After clearing debris, rake the entire prepared area to create a relatively smooth surface. This doesn't need to be perfectly smooth yet—that comes in later steps—but you're aiming to remove obviously uneven spots and any remaining loose material.

Practical Takeaway: Spend extra time removing rocks and roots. These items are the most common causes of pool damage, and addressing them now prevents expensive repairs later.

Leveling and Compacting the Ground

A level foundation is non-negotiable for above-ground pool safety. Pools should be level within 1 inch across the entire base. Many homeowners don't realize how much variation exists in their "level" yard—what looks flat often slopes slightly in one or more directions. Uneven pools develop stress on one side of the wall, leading to leaks and structural failure.

Find Your iPhone IMEI Number Guide →

Begin by determining the high and low points in your prepared area. Use a long straight board—a 2x4 or 2x6 lumber works well—and a basic level. Lay the board across your pool area in different directions and check it with the level. Mark the high and low points. The difference between highest and lowest points typically ranges from 2-6 inches on most residential yards.

Start at the lowest point and work toward the high areas. If you have significant slopes, you may need to remove soil from high areas and redistribute it to low areas. Some people rent a small excavator for this step (typically $200-$400 per day with delivery), while others do it manually with shovels. For areas with slight slopes, manual work is reasonable. For areas with major slopes, renting equipment saves significant labor.

As you level, compact the soil. This prevents settling after installation. Compaction can be done with a hand tamper (a flat metal plate on a handle), which costs $20-$40 to purchase or $5-$10 per day to rent. For larger areas, rent a plate compactor for about $50-$80 per day. Walk across the prepared area repeatedly with a hand tamper, or use the plate compactor systematically across all sections. Properly compacted soil should feel firm underfoot and resist compression when you push on it.

Continue checking for level as you work. Once the area is fairly even, do a final detailed check with your straight board and level, measuring from multiple directions and diagonals across the pool area. The slight slope should never exceed