Free Guide to Maytag Dishwasher Filter Cleaning

Understanding Your Maytag Dishwasher Filter System

Maytag dishwashers contain filter systems designed to trap food particles, debris, and other materials that come off dishes during the wash cycle. These filters prevent particles from clogging the spray arms and pump system, which keeps your dishwasher running at peak performance. Most Maytag models manufactured from 2010 onward feature either a single-stage or dual-stage filter configuration. A single-stage filter consists of one removable component, while a dual-stage filter includes both a fine mesh filter and a coarser grinding filter that work together.

Get Your Free Homeless Shelter and Financial Assistance Guide →

The primary filter is typically located at the bottom of the dishwasher tub, directly beneath the lower spray arm. This location allows water and food particles to flow toward the filter during the wash and rinse cycles. Understanding your specific model's filter type matters because cleaning procedures vary slightly between configurations. Maytag includes filter information in the owner's manual, which you can find by searching the model number on Maytag's website.

Over time, filters accumulate a buildup of grease, soap residue, and food fragments. This accumulation reduces water flow efficiency and can lead to dishes that come out spotted or unclean. Some particles may even bypass the filter and create blockages in other parts of the machine. Studies on dishwasher maintenance show that filters cleaned regularly—typically every two weeks to monthly depending on usage—maintain optimal water circulation and cleaning performance. Homeowners who clean filters as part of routine maintenance report fewer service calls and longer appliance lifespans.

Practical Takeaway: Locate your filter at the bottom center of your Maytag dishwasher's tub. Check your owner's manual to determine whether your model uses a single or dual-stage filter system, as this affects your cleaning approach.

Step-by-Step Filter Removal Process

Removing your Maytag dishwasher filter requires minimal tools and takes only a few minutes. Start by ensuring the dishwasher is completely empty and cool—never attempt filter removal during or immediately after a wash cycle. Open the dishwasher door fully and look at the bottom of the tub. You should see a cylindrical or basket-shaped component, typically made of plastic or stainless steel mesh. This is your filter assembly.

Learn About Student Visa Options and Requirements →

Most Maytag filters twist out rather than slide out. Grasp the center knob or handle of the filter with both hands, and turn counterclockwise approximately one-quarter to one-half turn. You should feel it loosen. If the filter is stuck due to mineral deposits or grease buildup, do not force it—instead, soak the area with warm water for 5-10 minutes to soften the debris, then try again. Once loose, gently pull the filter straight up and out of its housing. Set it on a clean towel or sink surface.

Some Maytag models feature a secondary coarse filter that sits beneath or around the main filter. This component may be labeled as a "grind chamber" or "coarse filter." If present in your model, you may need to remove this as well by twisting or unclipping it, depending on your specific design. Check your owner's manual or the filter itself for arrows or symbols indicating the proper removal direction. Taking a photograph of the filter in place before removal helps you remember the correct orientation when reinstalling.

If you encounter difficulty removing the filter after several attempts, consult your owner's manual for model-specific instructions. Different Maytag model lines sometimes use slightly different mounting systems. Forcing a stuck filter can crack the plastic housing or damage the threads, leading to leaks or improper water drainage.

Practical Takeaway: Always turn the filter counterclockwise to remove it. If stuck, apply warm water to loosen mineral deposits and grease before trying again.

Cleaning Techniques for Maximum Effectiveness

Once removed, rinse your Maytag filter under warm running water, using your fingers or a soft brush to remove loose food particles and debris. Aim the water spray from multiple angles to dislodge material trapped in the mesh. For light buildup occurring between monthly cleanings, rinsing alone may be sufficient. Hold the filter up to a light source and look through the mesh—you should see light passing through most of the surface. If the mesh appears dull or opaque, additional cleaning is needed.

Stop Google Notifications on Your Devices →

For filters with heavier buildup, create a soak solution using warm water and a small amount of white vinegar—approximately one part vinegar to four parts water. White vinegar contains acetic acid, which breaks down mineral deposits, grease, and soap scum without damaging the filter material. Submerge the filter in this solution for 15-30 minutes. The vinegar solution works particularly well if your area has hard water, as mineral deposits are common in those regions. After soaking, scrub gently with a soft-bristled brush, paying attention to the mesh areas where particles accumulate.

For stubborn grease deposits that vinegar alone cannot remove, a warm water soak combined with a small amount of dish soap works effectively. Use only a few drops of liquid dish soap mixed into warm water. Allow the filter to soak for 20 minutes, then use a soft brush to gently scrub away the grease. Never use abrasive scrubbing pads, wire brushes, or harsh chemical cleaners on your filter, as these can damage the mesh and create holes that allow particles to bypass the filter during future wash cycles.

If your filter has a secondary coarse filter component, clean this separately using the same techniques. The coarse filter typically has larger openings and accumulates less debris, but it still benefits from regular rinsing and occasional soaking. Rinse both components thoroughly under clean running water until the water runs clear and no soap or vinegar solution remains.

Practical Takeaway: Combine warm water rinsing with a vinegar soak for effective mineral and grease removal. Use only soft brushes to avoid damaging the mesh, and always rinse thoroughly until water runs clear.

Inspecting Your Filter for Damage and Wear

While cleaning your Maytag filter, take time to inspect it carefully for signs of damage or excessive wear. Hold the filter up to a bright light and look through the mesh from several angles. Small tears or holes in the mesh allow food particles to pass through, reducing the filter's effectiveness and potentially causing problems in other dishwasher components. If you notice any tears, holes, or areas where the mesh is missing, the filter should be replaced rather than reused.

Get Your Free Selkirk Shores Fishing Guide →

Check the plastic frame or housing surrounding the mesh for cracks, warping, or discoloration. Minor discoloration from hard water minerals or staining is normal and does not affect performance. However, cracks or warping can prevent the filter from seating properly in its housing, which allows water and particles to bypass the filter entirely. A filter that does not sit flush in its chamber compromises the entire filtration system.

Examine any rubber seals or gaskets on the filter. These components prevent water from leaking around the sides of the filter. If seals appear dried out, cracked, or hard, the filter may need replacement. Damaged seals cannot provide a watertight seal, which can lead to water pooling at the bottom of the dishwasher or leaking onto your kitchen floor. Some Maytag models allow you to replace just the seal without replacing the entire filter, while others require complete filter replacement.

If your filter shows no signs of damage, it can be reinstalled and used for future wash cycles. However, if you notice recurring cloudiness on dishes, standing water at the bottom of the tub, or unusual noises coming from the pump area even after cleaning, the filter may be damaged or failing in ways not visible during a simple inspection. In those cases, replacement is recommended. Maytag replacement filters typically cost between $25 and $75, depending on your specific model.

Practical Takeaway: Inspect the mesh for tears, the frame for cracks, and seals for damage. Replace any filter showing these signs of wear rather than attempting to reuse it.

Reinstalling Your Clean Filter Properly

Reinstalling your Maytag filter correctly is just as important as removal and cleaning. Before reinstalling, make sure your filter is completely dry or nearly dry—excess water should drip off, but the filter does not need to be bone-dry. Locate the filter housing at

Free Guide to Local Tree Removal Services →