Free Guide to Fixing Broken Glasses Arms

Understanding the Basic Structure of Eyeglass Frames

Before you attempt to fix a broken glasses arm, it helps to understand how the frame is built. Most eyeglass frames consist of several key components: the front portion (which holds the lenses), the two arms (also called temples), and the hinges that connect them. The arms are the long pieces that extend from the sides of the frame and wrap around your ears. Each arm typically has a hinge where it connects to the front of the frame, and many modern frames have what's called a spring hinge, which allows the arms to flex slightly for comfort and durability.

Social Security Office Hours and Holiday Information →

The hinge is often the weakest point in a glasses frame because it bears stress every time you put on or remove your glasses. When you open and close the arms repeatedly, the metal or plastic can fatigue and crack. Understanding this structure is important because different break locations require different repair approaches. A break right at the hinge requires different treatment than a break further down the arm, near where it wraps around your ear.

Most frames are made from materials like acetate (a type of plastic), metal alloys, or combinations of both. The material affects how you should repair it. Metal frames may require soldering or bonding agents designed for metal, while plastic frames need flexible adhesives that won't crack as the frame moves. Some frames have screws holding the hinge together, while others use rivets or are welded together at the factory.

Practical takeaway: Before starting any repair, examine where exactly your arm is broken. Is it at the hinge? Is it further along the arm? Is your frame primarily plastic or metal? These answers will guide which repair method will work best for your situation.

Assessing the Damage and Determining Repairability

Not all broken glasses arms can be successfully repaired at home. Some damage is too severe or requires professional equipment. Learning to assess the damage helps you determine whether a DIY fix is reasonable or whether you should visit an optometrist or eyewear repair shop. Start by examining the break carefully. If the arm has snapped cleanly into two pieces with a relatively straight break line, it's often repairable. If the break is jagged, splintered, or involves multiple pieces, repair becomes more difficult.

Get Your Free Guide to DMV Appointment Requirements by State →

Check whether the hinge mechanism itself is damaged. If the hinge is bent, cracked, or misaligned, this affects the repair strategy. Gently try to align the two broken pieces. If they fit together closely with minimal gaps, you have a better chance of creating a strong repair. If there are large gaps or missing pieces, you'll have fewer options. Also inspect whether the break is in the main body of the arm or at a point where the arm is particularly thin or flexible.

Consider the age and value of your glasses. If they're an inexpensive pair, investing significant time in repair might not make sense. However, if they're designer frames, prescription glasses you depend on, or glasses with sentimental value, repair efforts are more worthwhile. Also think about whether you can manage without your glasses while attempting repairs. Some fixes take time to set properly, and you don't want to rush the process by wearing damaged glasses before they're fully mended.

Practical takeaway: Assess whether your break is clean and close-fitting, whether the hinge is still functional, and whether the repair is worth your time and effort. If the break is complex or involves missing material, professional repair may be your better option.

Using Adhesives and Bonding Methods for Plastic Frames

For plastic frames with a broken arm, adhesive bonding is often the first repair approach to try. Several types of adhesives work for eyeglass frames, each with different strengths and application methods. Super glue (cyanoacrylate) creates a very quick bond and works reasonably well for plastic. However, super glue can be brittle and may not flex as the frame moves, potentially leading to the break reopening. A better option for glasses is plastic epoxy or two-part epoxy adhesive designed for plastics, which creates a more flexible bond that can withstand some movement.

Get Your Free Nordstrom Rack Credit Card Payment Guide →

Before applying any adhesive, clean both broken surfaces thoroughly. Use rubbing alcohol or a damp cloth to remove dust, oils, and debris. Let the surfaces dry completely. Align the two pieces carefully so they match up exactly as they were before the break. Some people find it helpful to test-fit the pieces first to ensure proper alignment. If you're using epoxy, mix it according to package directions, applying a thin, even layer to both surfaces. Press the pieces together firmly and hold them in position for the time specified on the package—typically several minutes.

After the adhesive sets, you may want to reinforce the repair. A common technique is wrapping the repair area with thin tape or athletic wrap to provide additional support. Some people use a thin layer of clear-drying epoxy over the repair site as reinforcement. This helps distribute stress and prevents the break from reopening when you wear and remove your glasses. Allow the repair to cure fully (usually 24 hours) before wearing the glasses. Even after curing, treat the repaired arm gently for the first few days.

Practical takeaway: Clean the break surfaces thoroughly, choose an epoxy or plastic-specific adhesive rather than super glue, ensure perfect alignment before bonding, and reinforce the repair with tape or additional epoxy once the initial bond sets.

Reinforcing and Supporting Broken Arms

A repair using adhesive alone may not provide enough strength, especially if you wear your glasses daily. Reinforcement techniques add structural support and help prevent the repair from failing again. One common method involves creating a splint along the break. You can fashion a splint from various materials: medical tape, athletic wrap, or even thin strips of plastic. Wrap the splint around the arm in the area of the break, covering several inches on either side of the break point. This distributes the stress across a larger area rather than concentrating it right at the break line.

Learn How to File a Small Claim Yourself →

Another reinforcement approach involves adding material inside the arm if possible. Some eyeglass arms are hollow or semi-hollow. If you can access the interior, a thin metal rod, wooden dowel, or even a straightened paper clip can be inserted as internal reinforcement. This provides structural support similar to how rebar reinforces concrete. You would secure this internal support with adhesive, then seal the arm opening if necessary.

For metal frames, you have additional options. Wrapping the break area with thin wire, tightly and neatly wound around the arm, creates reinforcement. You can then apply epoxy over the wire wrapping to lock it in place and improve appearance. Some people use dental floss or other strong, thin cordage for this purpose, applying multiple tight wraps. Metal frames may also benefit from having a professional jeweler or watch repair person solder the break, which creates a permanent bond stronger than adhesive alone.

Practical takeaway: Reinforce adhesive repairs by wrapping the area with medical tape or athletic wrap, consider adding internal support if the arm is hollow, and for metal frames, explore wire wrapping or professional soldering as reinforcement options.

Temporary Fixes and Solutions While Seeking Professional Repair

Sometimes you need your glasses to function while you arrange for proper repair. Temporary fixes allow you to continue wearing your glasses without risking further damage. Electrical tape or duct tape provides quick temporary support. Wrap the tape around the break area multiple times, covering several inches above and below the break point. Press it firmly and smooth out air bubbles. While this won't last indefinitely, it can keep your glasses functional for several days or weeks, depending on how carefully you wear them.

Learn About Dental Implants in Seattle →

Moleskin (the adhesive-backed material used for blister prevention) works surprisingly well for temporary arm support. It's thinner and more flexible than duct tape, so it looks somewhat less obvious. Apply it smoothly around the break area, similar to how you'd apply tape. The adhesive backing keeps it securely in place. Another option is athletic or sports wrap, which is designed to stay on skin and holds well on eyeglass frames too. It's flexible, breathable, and comes in various colors to better match your frame color.

If your break is at the hinge, you may be able to temporarily stabilize it by tightening the hinge screw if one exists. Some frames have a small screw on the outside of the hinge that you can carefully tighten with a very small screwdriver (often a jeweler's screwdriver or precision screwdriver set). Don't over-tighten, as this can damage the