Free Guide to Changing Your Oxygen Tubing

Understanding Oxygen Tubing Basics

Oxygen tubing, also called nasal cannula tubing or delivery tubing, is the flexible plastic tube that carries oxygen from your oxygen concentrator, liquid oxygen system, or oxygen tank to your nose. This tubing comes in different diameters and lengths, typically ranging from 25 feet to 50 feet, though custom lengths can be obtained. The tubing is usually made of medical-grade plastic that is clear or translucent, allowing you to see if condensation or water has accumulated inside.

Get Your Free iPhone Phone Blocking Guide →

The tubing connects to the oxygen delivery device at one end—whether that's a nasal cannula (the piece that goes in your nostrils), a face mask, or another delivery method. At the other end, it connects to your oxygen supply source. Most standard oxygen tubing has a diameter of approximately 3/16 inches on the inside, which allows for adequate oxygen flow while maintaining manageable weight and flexibility.

Over time, oxygen tubing can develop problems. The plastic may become cracked, kinked, or degraded from exposure to sunlight, heat, or simply from regular use and bending. If your tubing has visible damage, cracks, or holes, oxygen will leak out, meaning you won't receive the full dose of oxygen your doctor prescribed. Water droplets can also accumulate inside the tubing, especially if you're using a humidifier with your oxygen system, and this moisture can block oxygen flow or promote bacteria growth.

Most people need to change their oxygen tubing every 2 to 4 weeks, though some sources recommend monthly replacement. If you notice any cloudiness inside the tubing, persistent moisture, cracks, or decreased oxygen flow, you should replace the tubing sooner rather than later.

Practical Takeaway: Inspect your oxygen tubing regularly. Look for visible cracks, kinks, discoloration, or moisture inside the tube. If you see any of these signs, plan to change your tubing soon.

What You'll Need to Have Ready

Before you begin changing your oxygen tubing, gather all necessary supplies in one location. You'll need a new length of oxygen tubing that matches the specifications your doctor or oxygen supplier recommended. Make sure the new tubing is the correct diameter and length—ordering the wrong size will mean another trip to get the right equipment.

Find a Towing Company Near You Fast →

You should have the following items available: your new oxygen tubing, scissors or a utility knife to remove the old tubing if it's tightly attached, a clean cloth or paper towels for wiping connection points, and optional but helpful items include isopropyl alcohol (70% concentration) for cleaning connector points, a small bucket of warm water if you need to soften tight connections, and a trash bag for disposing of the old tubing properly.

Before starting, locate your oxygen supply source and understand how your particular system connects. Different oxygen systems work differently. A concentrator typically has a connection port on the back or side where tubing attaches. Liquid oxygen systems have a similar port. Portable tanks have a regulator valve at the top. Knowing exactly where your tubing connects prevents confusion during the replacement process.

Have your oxygen prescription information available. Your prescription should list the oxygen flow rate (typically measured in liters per minute, or LPM) that you need. This is important because you'll want to verify that your new tubing and connections support your prescribed flow rate. Most standard tubing supports flow rates from 1 to 6 LPM without problem, but it's worth checking.

Read through the instruction manual for your specific oxygen equipment if you have it. Different manufacturers may have slightly different connection methods. If you've misplaced your manual, many manufacturers post them online for free download on their websites.

Practical Takeaway: Create a simple checklist before you start: new tubing (correct size), old tubing to remove, cleaning supplies, your oxygen system manual, and your prescription information. Having everything ready prevents frustration during the process.

Steps for Removing Your Old Tubing

The first step in changing your oxygen tubing is safely removing the old tubing. Before you begin, turn off your oxygen system at the concentrator, tank, or liquid oxygen unit. This is important for safety and prevents oxygen from flowing out of the connection point while you're working. If you wear a nasal cannula, gently remove it from your nostrils and set it aside on a clean surface.

Your Free Guide to Indiana Driver's License and Vehicle Registration →

Look at where the tubing connects to your oxygen supply source. Most connections use a simple push-fit connector or a threaded fitting. For push-fit connectors, gently pull the tubing straight out from the port. You may need to wiggle it slightly as you pull, but forcing it can damage the connection port. If the tubing is stuck, soak the connection area with warm water for a minute or two to soften any plastic that may have become slightly fused to the connector.

For threaded connections, you'll notice the tubing has a fitting that screws onto the port. Turn this fitting counterclockwise (lefty-loosey, righty-tighty applies here) until it's loose enough to unscrew by hand. Once loose, finish unscrewing it and gently pull the tubing away from the oxygen source.

After you've removed the tubing from the oxygen source, remove it from your nasal cannula or other delivery device. Again, most connections are simple push-fit, so gently pull the tubing away. If it's threaded, turn counterclockwise to loosen.

Examine the connection ports on your oxygen source and your cannula or delivery device. Look for any visible debris, dust, or dried residue. Use a clean, dry cloth to wipe away any dust or particles from these connection points. If there's sticky residue, use isopropyl alcohol on a cloth to clean it gently. Allow any alcohol to evaporate before reconnecting new tubing. Don't leave your oxygen source uncovered for an extended period—if it has a protective cap, you can place it loosely over the port while you're preparing the new tubing.

Practical Takeaway: Turn off your oxygen supply first. Take your time removing old tubing—gentle pulling and wiggling works better than forcing. Clean connection points with a dry cloth before attaching new tubing.

Installing Your New Oxygen Tubing

Once you've removed the old tubing and cleaned the connection points, you're ready to install the new tubing. Begin at the oxygen source end. Take one end of your new tubing and examine the connection fitting. It should be smooth and undamaged. If it seems kinked or pinched from being stored, you can gently straighten it under warm water for a moment.

Delete Your Uber Account Permanently Guide →

For push-fit connections, push the tubing connector firmly into the port on your oxygen source until you feel it seat securely. You should feel slight resistance and hear a small click. Don't use excessive force—a firm push is sufficient. For threaded connections, insert the fitting and turn clockwise until it's snug. You want it tight enough that tubing won't pull out, but not so tight that you're straining to turn it.

Now, before you connect the other end of the tubing to your nasal cannula or delivery device, you should run your oxygen system for 10 to 20 seconds to clear any dust or particles from the new tubing. This step removes manufacturing residue that may be inside new plastic tubing. Let the oxygen flow out of the open tubing end for a short time, then proceed to connect it to your delivery device.

Take the other end of the tubing and connect it to your nasal cannula, face mask, or other delivery device. Use the same method as the first connection: push-fit or threaded, depending on your equipment. Make sure this connection is also secure.

Before you turn your oxygen back on to full flow, visually inspect the entire length of tubing. Make sure there are no kinks, twists, or areas where the tubing is pinched. Lay it out in a relatively straight path from your oxygen source to where you'll be sitting or lying. Oxygen tubing should be routed away from hot surfaces like radiators or sunny windowsills, as heat can degrade the plastic over time.

Once everything is connected and the tubing is positioned properly, turn your oxygen supply back on. If you're using a concentrator, you'll hear it start up. Check the flow meter to make sure oxygen is flowing at your prescribed rate. If