Free Guide to Changing Your Car's Motor Oil

Understanding Your Car's Oil and Why It Needs Changing

Motor oil serves as the lifeblood of your engine, performing several critical functions that keep your vehicle running smoothly. Oil lubricates moving parts within the engine, reducing friction between metal surfaces that would otherwise wear down quickly. Without adequate lubrication, engine components would generate excessive heat and eventually seize up, causing catastrophic engine failure. Beyond lubrication, oil also absorbs heat generated by combustion, helps seal the engine's pistons and cylinders, and carries away dirt and debris that accumulates during normal engine operation.

Free Guide to Understanding NPI Updates →

Over time, motor oil breaks down due to exposure to high temperatures, oxidation, and contamination from combustion byproducts. A typical oil change interval for most modern vehicles ranges from 3,000 to 10,000 miles, depending on the vehicle manufacturer's recommendations and the type of oil used. Synthetic oils generally last longer than conventional oils—some synthetic oils can go 8,000 to 10,000 miles between changes, while conventional oils typically need replacement every 3,000 to 5,000 miles. Neglecting oil changes can result in increased engine wear, reduced fuel economy, and potential engine damage that may cost thousands of dollars in repairs.

Your vehicle's manufacturer specifies the correct oil type and viscosity grade for your engine. The viscosity grade appears as a number and letter combination, such as 5W-30 or 10W-40. The number before the "W" (which stands for winter) indicates the oil's thickness in cold temperatures, while the number after the dash indicates its thickness at normal operating temperature. Using the wrong oil viscosity can affect engine performance and protection. Checking your owner's manual or the inside of your fuel door will typically provide the correct oil specification for your specific vehicle.

Takeaway: Regular oil changes extend engine life and maintain performance. Check your owner's manual for your vehicle's specific oil type and recommended change interval, and plan your maintenance accordingly.

Tools and Materials You'll Need

Changing your oil requires relatively few tools and materials, many of which you may already have at home. The essential items include a socket wrench set with the correct size socket for your oil drain plug (typically 13mm, 14mm, or 15mm), an oil filter wrench to remove and install the filter, and a jack and jack stands to safely lift your vehicle. Never rely solely on a jack to support your vehicle while you work underneath it—jack stands are critical safety equipment that prevents serious injury or death from a falling vehicle.

Get Your Free Skechers Shoe Cleaning Guide →

You'll also need an oil drain pan to catch the old oil as it drains from your engine. Any container that can hold at least 5-6 quarts of liquid will work, though actual oil drain pans designed for this purpose cost between $10 and $30 and make the process cleaner. A funnel designed for oil changes helps you pour new oil into your engine without spilling. Rags, old towels, or shop towels are essential for cleaning up spills and wiping away excess oil. Many people keep a supply of these inexpensive supplies specifically for car maintenance work.

The supplies you'll need to purchase include new motor oil in the quantity specified by your owner's manual (typically 4 to 8 quarts depending on your vehicle), a new oil filter, and potentially a new drain plug gasket. The cost of these materials typically ranges from $25 to $75, depending on whether you choose conventional or synthetic oil and your vehicle's specifications. Some vehicles require special drain plug gaskets that cost $1 to $5, while others use crush washers that come included with replacement drain plugs.

Optional but helpful items include a creeper (a wheeled board that lets you lie on your back and roll under the vehicle), a headlamp to see better in the engine compartment, a socket extension to reach difficult drain plugs, and absorbent materials like kitty litter to handle any spills. Many people find that setting up a clean workspace with these items beforehand makes the job go more smoothly and safely.

Takeaway: Invest in quality jack stands and an oil drain pan as your foundation tools. You can acquire other items gradually, but prioritize safety equipment before attempting any work under your vehicle.

Step-by-Step Process for Draining Old Oil

Begin by warming your engine to operating temperature by running it for a few minutes. Warm oil flows more freely than cold oil, allowing it to drain completely and carry away more contaminants. However, be careful not to burn yourself—the engine and oil will be hot. Turn off the engine and wait a minute or two for the most extreme heat to dissipate before proceeding. Never work on a vehicle that's in gear or in drive; always set the parking brake and place the transmission in park or neutral.

Free Guide to USAA Insurance Membership Requirements →

Safely lift your vehicle using a jack, then position jack stands under the vehicle's frame or designated lifting points (consult your owner's manual for the correct locations). Lower the vehicle onto the jack stands so they're supporting the weight. Double-check that the vehicle is stable before crawling underneath. Locate your oil drain plug—it's typically a bolt at the lowest point of the oil pan, which is the large metal container under your engine. Position your drain pan directly underneath the drain plug.

Using your socket wrench, turn the drain plug counterclockwise to loosen it. Once it's loose enough, carefully unscrew it by hand, letting the oil flow into your drain pan. Be prepared for the oil to flow quickly and splash—some people rotate the drain plug so the oil flows away from their body. Allow the oil to drain completely, which typically takes 5 to 10 minutes. While waiting for the oil to drain, you can locate your oil filter, which is usually a cylindrical canister mounted to the side of the engine.

Once the oil has stopped dripping, wipe the drain plug clean with a rag and inspect the crush washer (a small metal ring at the bottom of the plug). If it appears cracked or damaged, replace it or use a new drain plug. For the drain pan, you may have noticed a fine metal mesh or small drain threads at the bottom—some drain pans allow you to drain the collected oil into a container for proper recycling at a waste facility or auto parts store.

Takeaway: Take your time with the drain plug to avoid stripping it or spilling oil. Allowing complete drainage ensures maximum contamination removal and prevents overfilling with the new oil.

Replacing the Oil Filter

The oil filter removes contaminants from your oil as the engine runs, gradually accumulating particles over thousands of miles. Replacing it simultaneously with your oil change ensures optimal filtration and engine protection. Most oil filters are cylindrical canisters mounted vertically on the engine, though some vehicles use cartridge-style filters located in a housing on top of the engine. Consult your owner's manual or a quick visual inspection of your engine will show you which type your vehicle uses.

Free Guide to Understanding Shipping Cost Calculations →

For canister-style filters, position your drain pan underneath the filter (old oil will drain out when you remove it). Using an oil filter wrench, grip the filter's circumference and turn it counterclockwise to loosen it. Once loose, unscrew it by hand, being careful not to spill the remaining oil inside. Check the filter mounting surface on the engine to ensure the rubber seal from the old filter has been removed—sometimes this rubber ring sticks to the engine. If it's still there, carefully peel it off to avoid damaging the mounting surface.

Before installing the new filter, apply a thin layer of new motor oil around the rubber gasket (the seal) on top of the filter. This helps create a watertight seal and makes the filter easier to remove next time. Screw the new filter onto the mounting surface by hand. The common practice is to tighten it until the gasket contacts the mounting surface, then turn it an additional three-quarter turn. Over-tightening can damage the filter or make it difficult to remove during the next oil change. The filter should be snug but not excessively tight—hand-tight is the goal.

For cartridge-style filters, the process is similar but requires opening a housing cap rather than dealing with a spin-on canister. Remove the cap, lift out the old filter element, and inspect the inside of the housing for debris. Clean any particles from the housing before inserting the new filter element. Reinstall the cap, hand-tightening it firmly.

Takeaway: The oil filter gasket seal is critical—don't forget